R SPRING NECK OWNER’S MANUAL INSPIRED BY
TABLE OF CONTENTS Product Information..............................1 Parts, Tools, Maintenance.....................3 Installation.....................................................5 Troubleshooting........................................11 Warranty..........................................................13 TABLE DES MATIÈRES Information produit...............................1 Pièces, Outils, Entretien.......................3 Installation.....................................................5 Dépannage..
PRODUCT INFORMATION Information produit Product Features Caractéristiques du produit • Metal lever handle • 2 function spray head • Single-hole or 3-hole installation • Drip-free ceramic cartridge • 1.
PRODUCT DIAGRAM Diagramme de produit 2
PARTS Les Pièces Spray Head Faucet Tête de pulvérisation Robinet Counter Weight Contrepoids Mounting Hardware (rubber washer, metal washer, mounting nut, screws set) Deck Plate Plaque de pont Matériel de montage (rondelle de caoutchouc, rondelle métallique, écrou de montage, jeu de vis) Aerator Key Clé d’ aérateur RECOMMENDED TOOLS (NOT INCLUDED) OUTILS RECOMMANDÉS (Non Inclus) • Adjustable Wrench • Screwdriver • Clé à molette • Tournevis Parts, Tools, Maintenance | Pièces, Outils, Entretien
MAINTENANCE Entretien Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and void your warranty. Votre nouveau robinet est conçu pour des années de performance sans problème Gardez l’aspect neuf en le nettoyant périodiquement avec un chiffon doux.
INSTALLATION Installation NOTE: Flush water lines before installation to release built up impurities of water supply. REMARQUE: Rincez les conduites d’eau avant l’installation pour libérer les impuretés accumulées dans l’alimentation en eau. Step 1 for 1-hole sink Fit the white washer (or flange) over the hoses to the mounting shank, Then fit the faucet to the mounting hole on the sink, or fit the faucet to the mounting hole if no washer or flange is provided.
rubber washer faucet shank metal gasket mounting nut screw Step 2 Étape 2 Slide the rubber washer first, the metal gasket second, and then the mounting nut over the hoses onto the shank. Hand tighten them firmly. Use a cross scredriver to thread the 2 screws. Faites glisser la rondelle en caoutchouc en premier, le joint métallique en second, puis l’écrou de montage sur les tuyaux sur la tige. Serrez-les fermement à la main. Utilisez un tournevis cruciforme pour visser les 2 vis.
Attention (avoid hose crimps) Hot Supply Hose Cold Supply Hose Step 3 Étape 3 Connect the hot and cold supply lines onto the matching water valves and secure the connection with an adjustable wrech. Branchez les conduites d’alimentation chaude et froide sur les vannes d’eau correspondantes et fixez la connexion avec un wrech réglable. CAUTION: Risk of property damage. Do not overtighten connections. This will prevent water leakage.
Push Weight Locator Mark Step 4 Step 5 Connect the spray hose to the quick connection just by a simple push. Install the quick-connect counterweight on the pull-down hose at the marked postition. (It should be placed on the line.) Turn on the water valves and then test the faucet. Run the water flow for 15 seconds to clean up the lines and check for any leaks. Étape 4 Ouvrez les vannes d’eau, puis testez le robinet.
Step 6 Step 7 Attach and secure the spray head onto the pulldown hose. To check the faucet head, remove the aerator using the blue aerator key. Unscrew and clean out any mineral build-up inside the faucet head. Reattach the aerator, turn on the water valves, and start the faucet to check for a difference in water flow rate. Étape 6 Fixez et fixez la tête de pulvérisation sur le tuyau déroulant. WARNING: Risk of Scalding. High water temperature can cause severe burns.
Step 8 Step 9 Turn on water to make sure the water runs correctly. Switch from spray mode to stream mode a few times to make sure the switch opperates properly. Check for leaks. After installation is complete, turn on the faucet and do a final check for any leaks. Étape 8 Une fois l’installation terminée, ouvrez le robinet et effectuez une dernière vérification pour déceler toute fuite. Ouvrez l’eau pour vous assurer que l’eau coule correctement.
FLOW CLASSIC FAUCET TROUBLESHOOTING GUIDE ROBINET FLOW CLASSIC GUIDE DE DÉPANNAGE Condition | État Possible Cause | Cause possible Water dripping occurs when the handle is in the OPEN position. Water drips from the faucet. Water flow is diminished De l’eau coule du robinet. Water dripping occurs when the handle is in the CLOSE position. Faucet handle is not open fully. Filters may have debris. Des gouttes d’eau se produisent lorsque la poignée est en position OUVERTE.
Solution | Solution Manual override might be slightly open. Close the manual override on the control box by turning the knob clockwise until completely closed. Change the faucet cartridge. Open the handle fully and test the flow. If the water flow is still diminished, clean the filter found in the top part of the black control box and clean the aerator and nipples on the faucet head. La commande manuelle peut être légèrement ouverte.
5 YEAR WARRANTY FLOW Motion Activated Kitchen Faucet comes with a 5year warranty from date of purchase 100% Coverage on all parts and labor for the entire product for all five years from original date of purchase. Our obligations under this warranty are limited to repair or replacement, at our option, of products or parts found to be defective, provided that such products were properly installed and used in accordance with instructions.
This written warranty is the only warranty made by BBC. Repair or replacement as provided under this warranty shall be the exclusive remedy available to the purchaser. We shall not be responsible for loss of the product or for other incidental, special, or consequential damages or expenses incurred by the purchaser, or for labor other costs due to installation or removal or costs of repairs by others, or for any other expense not specifically started above.
GARANTIE 5 ANS Le robinet de cuisine activé par le mouvement FLOW est livré avec une garantie de 5 ans à compter de la date d’achat Couverture à 100% sur toutes les pièces et main-d’œuvre pour l’ensemble du produit pendant les cinq années à compter de la date d’achat d’origine.
Cette garantie écrite est la seule garantie offerte par BBC. La réparation ou le remplacement tel que prévu dans le cadre de cette garantie sera le recours exclusif à la disposition de l’acheteur.
Thank You BBC Innovation Corporation 7900 S Route 31 Crystal Lake, IL 60014 support@biobidet.com biobidet.
