Installation and Operation Instructions
Table Of Contents
- Chapter 1 Important information
- Chapter 2 Document and product information
- 2.1 Product documentation
- 2.2 Product overview
- 2.3 Applicable products
- 2.4 Parts supplied
- 2.5 Licensing
- USA licensing requirements
- Canada licensing requirements
- Europe and rest of world licensing requirements
- Additional information — Ray90 / Ray91
- Additional information - wireless handset
- Additional information - wireless charging holster
- Additional information - wireless hub
- Additional information - wireless speaker
- 2.6 Obtain MMSI (Maritime Mobile Service Identity) number
- 2.7 Automatic Transmitter Identification System (ATIS)
- 2.8 Software updates
- Chapter 3 Installation
- Chapter 4 Cables and connections
- 4.1 General cabling guidance
- 4.2 Connections overview
- 4.3 Power connection
- 4.4 Handset station connection
- 4.5 Wired speaker connection
- 4.6 NMEA 2000 / SeaTalkng® connection
- 4.7 NMEA 0183 connection
- 4.8 Loud hailer connection
- 4.9 Connecting GNSS (GPS) and VHF antennas
- 4.10 Wireless hub connection
- 4.11 Wireless handset charging holster – power connection
- 4.12 Wireless handset connections
- 4.13 Wireless speaker – power connection
- Chapter 5 Getting started
- 5.1 Handset controls
- 5.2 Powering the Base station
- 5.3 Homescreen overview
- 5.4 Multiple station operation
- 5.5 Adjusting Brightness and Contrast
- 5.6 Shared Brightness
- 5.7 Initial set up
- 5.8 Selecting a language
- 5.9 Switching on the AIS receiver
- 5.10 Selecting a network type
- 5.11 Entering your MMSI number
- 5.12 Entering your ATIS ID
- 5.13 Changing the radio region
- 5.14 Switching between high and low transmit power
- 5.15 GNSS (GPS) set up
- Chapter 6 Wireless handset stations
- Chapter 7 Digital selective calling (DSC)
- 7.1 Digital Selective Calling (DSC)
- 7.2 Distress calls
- Making a designated distress call
- Making a Distress call
- Making a Mayday call
- Cancelling a distress call before transmission
- Cancelling a distress call after transmission
- Receiving a distress call
- Ignoring a distress call
- Acknowledging a distress call
- Manually relaying a distress call
- Distress relays sent by other stations
- 7.3 Urgency calls
- 7.4 Safety calls
- 7.5 Individual (routine) calls
- 7.6 Group calls
- 7.7 Position requests
- 7.8 Phonebook
- 7.9 Call logs
- 7.10 Test calls
- 7.11 DSC set-up menu options
- Chapter 8 VHF operations
- Chapter 9 Hailer, Fog horn, and Intercom
- Chapter 10 Maintenance
- Chapter 11 Troubleshooting
- 11.1 LED diagnostics — Ray90 / Ray91 Base station
- 11.2 LED diagnostics - Wireless (Active) speaker
- 11.3 Troubleshooting
- 11.4 Power up troubleshooting
- 11.5 Audio troubleshooting (transmission / reception)
- 11.6 GNSS (GPS) troubleshooting
- 11.7 DSC troubleshooting
- 11.8 AIS troubleshooting (Ray70 / 73 / 91 only)
- 11.9 Wired handset troubleshooting
- 11.10 Wireless troubleshooting (Ray63 / 73 / 90 / 91 only)
- Chapter 12 Technical support
- Chapter 13 Technical specification
- 13.1 Technical specification — Base station
- 13.2 Technical specification — Wired handset (Raymic)
- 13.3 Technical specification - Wired (Passive) speaker
- 13.4 Technical specification - Wireless hub
- 13.5 Technical specification - Wireless handset
- 13.6 Technical specification - Wireless handset charging holster
- 13.7 Technical specification - Wireless (Active) speaker
- 13.8 Radio usage
- Chapter 14 Spares and accessories
- Appendix A NMEA 0183 sentences
- Appendix B NMEA 2000 PGN list
- Appendix C MMSI Regulatory bodies and application submissions
- Appendix D VHF Channels
- Appendix E Phonetic alphabet
- Appendix F Prowords
- Blank Page
1.Checktheselectedlocationforthemountingholster
,
aclearflatareaisrequired,withsufficientspace
aroundittoplaceandremovethehandset.
2.Usingapencil,offeruptheholstertothedesired
locationandmarkthelocationofthescrewholes
onthemountingsurface.
3.Drillthemountingholesusingasuitablesizedrillbit.
4.Holdtheholsterinplaceandsecureusingthe
screwsprovided.
5.Placethehandsetintotheholsteruntilitclicksinto
position.
Pass-throughpanelkitmounting
Wheninstallinghandsets,thepass-throughpanelkit
shouldbeusedtosecurethecable’sconnectortothe
panelthecablehastopassthrough.
1
Splash-proofdustcapwithlanyard
2Mountingplatefixingsx3
3
Mountingplatenut
4Mountingplate
5Mountingplategask
et
6
Extensioncable
1.ChecktheselectedlocationfortheMountingplate
,a
clearflatareaisrequired.
2.Ensuringcorrectorientationofthemountingplate,
offeruptheplatetothedesiredlocationandmark
thelocationofthescrewholesandthecenterhole
onthemountingpanel.
Toensurethatthehandset’sconnectorpointsdown
whenconnected,orientatethemountingplateso
thatthelanyardgroveispointingstraightup.
3.Drillthemountingholesusingasuitablesizedrillbit.
4.Drillthecenterholeusinga25mm(1in.)holecutting
saw.
5.Pulltheconnectorendofthecablethroughthehole
inthemountingsurface.
6.PlacetheMountingplategasketovertheendofthe
connector.
7.Withtherecessedsidefacingawayfromthe
mountingpanel,placetheMountingplateoverthe
endoftheconnector.
8.PlacethelanyardendoftheSplash-proofdustcap
overtheconnector,ensuringthelanyardsitsinthe
recessintheMountingplate.
9.PlacetheMountingplatenutovertheconnectorand
tightenclockwiseusinga13/16in.(21mm)socket
wrench,beingcarefulnottodamagetheplasticnut
byovertightening.
10.SecuretheMountingplatetothemountingsurface
usingthesuppliedscrews.
11.AttachtheHandset/Fistmicconnectortothecable
connectorandrotatethelockingcollarclockwiseto
secure.
12.Connecttheoppositeendofthecabletothe
requiredconnectoreitherontheBasestationor
toanotherpass-throughpanelmountingplate
connector.
Note:
Drillbit,tapsizeandtighteningtorqueisdependent
onthethicknessandtypeofmaterialtheunitisto
bemountedon.
Mountingthewirelesshub
Beforemounting,ensurethat:
•yourselectedlocationmeetsthelocation
requirementsfoundinthisdocument.
•youpayparticularattentiontothewirelesslocation
requirements.
•sufficientspaceisavailableaboveortoonesideof
thehubfortheantenna.
•theproductoperatescorrectlyatthedesiredlocation
beforemounting.
Installation29
81377-6-en-US_A5_PRINT.pdf 29 5/4/2020 3:32:52 PM