Owner manual

ManualsBrandsFlint & Walling ManualsPumpsCCF Series Air Induction Water Treatment Systems

FILL IN FOR FUTURE REFERENCE

MODEL NO:___________________________________________

DATE INSTALLED:______________________________________

DEALER:______________________________________________

INSTALLATION, OPERATION, AND

MAINTENANCE MANUAL

CBW10, CBW10D, CBW20, CBW20D

CCF10, CCF10D, CCF20, CCF20D

(Addendum Included)

AUTOMATIC WATER

FILTERS

PP0131

0611

Supersedes

0610

SPECIFICATION TABLE

Units

CBW10,

CBW10D

CCF10,

CCF10D

CBW20,

CBW20D

CCF20,

CCF20D

Service Flow

(1)

Cont. GPM 3 3 5 5

Peak GPM 8 8 10 10

Pipe Size In/Out - Inches 1” 1” 1” 1”

Operating Pressure Range PSI 30 - 125 30 - 125 30 - 125 30 - 125

Max Operating Temperature Degrees F 110 110 110 110

Mineral Tank Size (Dia. x Ht.)

(2)

Inches 10 x 44 10 x 44 12 x 52 12 x 52

Shipping Weight Lbs. 47.5 137 57.5 235

Overall Height Inches 52 52 60 60

Drain Flow During Regeneration

(3)

GPM 5.3 6.5 7.5 7.5

NOTE:

(1)

Pressure drop not to exceed 15 psi.

(2)

Product materials and workmanship are protected with a written warranty.

(3)

Untreated water provided during all steps of regeneration.

023367

Summary of content (12 pages)

PAGE 1
PP0131 0611 Supersedes 0610 INSTALLATION, OPERATION, AND MAINTENANCE MANUAL CBW10, CBW10D, CBW20, CBW20D CCF10, CCF10D, CCF20, CCF20D (Addendum Included) AUTOMATIC WATER FILTERS SPECIFICATION TABLE Service Flow (1) Cont. Peak Pipe Size Operating Pressure Range Max Operating Temperature Mineral Tank Size (Dia. x Ht.
PAGE 2
Transformer Typical Water CBW Installation Filter Tank Assembly Drain Port Manual Inlet Valve (optional) Manual Bypass Valve (Normally Closed) (optional) Drain Trap Cold filtered water inlet 30 p.s.i. minimum pressure 1” minimum pipe size Drain IL1037 Sanitary Drain, Floor Drain or Laundry Tubs are acceptable. Do not make a direct connection to the drain. An air gap must be present. Drain line 1/2” ID diameter minimum size Maximum drain pipe elevation above drain port is 5 ft.
PAGE 3
® remier P P roducts Automatic Water Filters WATER TREATMENT Installation Fitting Assemblies Installation fittings connect to the control valve or the bypass valve using nuts that only require hand tightening. Hand tight nut connections between control valve and installation fittings, control valve and bypass valve, and bypass valve and installation fittings allow for ease serviceability. Do not use a pipe wrench to tighten nuts on installation fittings. Hand tighten only.
PAGE 4
® remier P P roducts Automatic Water Filters WATER TREATMENT occurs, household plumbing system must be flushed clean. C. CONNECT ALL FITTINGS (refer to previous page) 13. Models CBW10D, CBW20D, CCF10D and CCF20D have a dome hole/plug located in the upper dome of the mineral tank. This is used to replenish mineral as required. DO NOT remove dome hole plug without first depressurizing the tank. CAUTION: Care must be used when working with copper tubing.
PAGE 5
® remier P P roducts Automatic Water Filters WATER TREATMENT 3. L ocate in correct relationship to other water treatment equipment (See Figure 1). REGULATING VALVE MUST BE INSTALLED TO REDUCE WATER PRESSURE. 4. llow sufficient area around the equipment for A service. NOTE: Pressure regulating valve must be installed in water line ahead of the air induction assembly. FACTS TO REMEMBER WHILE PLANNING YOUR INSTALLATION CHECK PUMPING RATE OF WELL PUMP 1.
PAGE 6
® remier P P roducts Addendum for CCF Series Automatic Water Filters Only WATER TREATMENT BEFORE INSTALLING YOUR FILTER 4. INSPECTION AND HANDLING YOUR FILTER Be sure to inspect the equipment for shipping damage and notify the transportation company if damage exists. Handle the filter with care, as damage can result if dropped or if the filter is set on a sharp object. CHECK WATER PRESSURE Minimum water pressure required at the inlet of the filter is 30 psi.
PAGE 7
® remier P P roducts Addendum for CCF Series Automatic Water Filters Only WATER TREATMENT and pressure control switch is located on pressure tank side of the air induction assembly (See Figure 2). Allow 8” of straight pipe on both sides of air induction assembly. SUCTION PORT FLOW ADJUSTING SCREW WATER FLOW WATER FLOW IL1041 Figure 2 - Air Induction Assembly INSTALLING THE FILTER 1. Media was shipped separately. Carefully unscrew the control valve.
PAGE 8
® remier P P roducts Automatic Water Filters WATER TREATMENT D. PRESSURE TEST THE INSTALLATION The plumbing system can now be checked for any possible leaks STEP 1B - Setting Days Between Backwash: and buttons to set the days between Use the backwashes (factory default is 3 days). 1. Press Open the water supply inlet valve very slowly. Once the mineral tank is full of water, slowly open the outlet on the bypass. Open a faucet down stream from the filter & allow the air to escape.
PAGE 9
® remier P P roducts Automatic Water Filters WATER TREATMENT Bypass Valve The bypass valve is typically used to isolate the control valve from the plumbing system’s water pressure in order to perform control valve repairs or maintenance. The bypass valve is particularly unique in the water treatment industry due to its versatility and state of the art design features.
PAGE 10
Part No. 023406 023412 023408 023409 023410 127001 023362 023411 Item No. 1 2 3 4 5 6 7 8 Transformer 110V-12V Service Tool Mineral Fill Funnel O-Ring Kit Seal Assy. Piston Assy. PC Board Motor Description 1 1 1 1 1 1 1 1 Qty Service Tool Transformer Funnel IL1061 8 IL1049 6 WATER TREATMENT remier P P roducts IL1047 7 Turn counter-clockwise to remove. Turn clockwise to install.
PAGE 11
® remier P P roducts Automatic Water Filters WATER TREATMENT Item Description 1 CBW10 CBW10D CBW20 CBW20D CCF10 CCF10D CCF20 CCF20D Distributor tube / screen 023360 023360 023488 023488 023360 023360 023488 023488 023319 023320 023483 023491 023319 023320 023483 023491 * * * * 135523 135523 023529 023529 2 Mineral tank 3 Mineral 4 Gravel 023358 023358 023358(Qty 2) 023358(Qty 2) 135523 135523 023529 023529 Qty Application* Part # Description 1 2 CBW10 CBW20 CBW
PAGE 12
® remier P P roducts Automatic Water Filters WATER TREATMENT Table 6 - Troubleshooting Procedures Problem 1. T imer does not display time of day 2. T imer does not display correct time of day 3. C ontrol valve regenerates at wrong time of day 4. E1, E2, or E3 Possible Cause a. b. c. d. a. b. c. a. b. c. a. E1 - Unable to recognize start of regeneration b. E2 - Unexpected stall c. d. E3 - Motor ran too long, timed out trying to reach the next cycle position or trying to reach home position e.