User manual Flic 2
Getting started To get started make sure that you have: 1. An iOS or Android device with at least Bluetooth 4.0+ 2. Active internet connection 3. The Flic app, available on the App Store or Google Play 4. A Flic 2 button (”Flic”) For the up-to-date requirements and further information visit https://flic.
Connecting your Flic 1. Make sure Bluetooth is activated on your phone. 2. Open the Flic App, create an account and login. 3. Follow the setup guide in the app to get your Flic paired. 4. Now you are ready to set up your first actions.
Bluetooth connection When setting Flic up make sure to connect to your device through the Flic App. iOS users: an in-app pop up will ask you to confirm the Bluetooth connection with your device. Android users: do not try to pair with your Flic through the Bluetooth settings ‘Available devices’ page. Always keep your Bluetooth on to ensure your Flic stays connected with your device.
Sticking your Flic Each Flic comes with a reusable adhesive sticker, pre-attached to the back. Simply peel off the protective layer and stick your Flic on any clean surface. If you want to change the position of your Flic, twist the button to the right in order to exert horizontal force which makes it easier to remove the adhesive from the surface. Note: consider that the adhesive is super strong before you stick it to any surface. Removing the adhesive might damage the surface attached.
Cleaning the adhesive If the adhesive starts to lose its stickiness then you can clean it 1. Carefully wash off the adhesive with water. 2. Give it a rub and repeat the wash. 3. Leave it to air-dry and it will return to full stickiness. Flic is not waterproof. Do not expose it to rinsing water, submerge or attempt to use underwater as this will result in irreversible damage that is outside the scope of the Shortcut Labs AB warranty.
Wearing your Flic To wear Flic you will need to have a Metal Clip. In case if you do not have it, you can get it from our webshop. When all set, just simply expand the metal frame and carefully slide your Flic in the frame. Done! You are good to go.
Changing the battery To change the battery you will need to follow these steps: 1. Open the battery hatch, by sticking your Flic to a surface and twisting it to the left. 2. Remove the old battery and replace it with a new CR2032 battery with the “+” side facing towards you. 3. Place back the top part of Flic to the bottom and twist to the right until it clicks and the adhesive releases the surface. Note: consider that the adhesive is super strong before you stick it to any surface.
Factory reset If, for any reason, you must perform a factory reset, perform the following steps: 1. Remove the battery, see the page “Changing the battery”. 2. Insert the battery. 3. Within 5 seconds push and hold the button for 10 seconds. By pushing the button, all your settings will be lost and the Flic will return to default.
Problems If you have any issues setting up or using the Flic products that are not answered here, please read FAQ’s at https://start.flic.io/faq Alternatively, you can contact us via flic.io/support Compliance Shortcut Labs declaration of conformity is available at https://flic.io/doc For full compliance, list visit https://flic.io/compliance Flic 2 is certified as FCC, IC, CE, AUS, R-NZ and WEEE, RoHS, REACH compliant.
Handling the battery This device contains a CR2032 battery composed of lithium, organic solvents, and other combustible materials. For this reason, improper handling of the battery could lead to distortion, leakage, overheating, explosion or fire, causing personal injury. Please observe the following instructions to prevent accidents. Never swallow charge, heat, expose to open flames, moisture or liquid. Never attempt to disassemble, reverse the polarity or short circuit. Keep away from children and pets.
Safety usage guidelines The Flic is not a toy. It contains small parts and accessories that present a choking hazard. As such it is not suitable for children or pets. General - Do not attempt to service the product. - Do not use the product in temperatures below -10°C or above +40 °C. - Clean with a damp cloth only. Do not submerge and do not use chemical or abrasive cleaning products. Flic specific - Battery life will be shortened with heavy usage and/or use in extreme conditions. - Flic is not waterproof.
Warranty Shortcut Labs AB warrants that your Flic hardware product (“the product”) will be free from defects in materials and workmanship for a period of 24 months from the date of delivery to the original retail purchaser (“the warranty period”).
Notice Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Join us! https://community.flic.io/ Share your ideas with other Flic users and keep up to date with the latest news and happenings from the Flic team.
