User Manual

ManualsBrandsFlex ManualsHardwareFLC Coping

Flexcap FLC Coping

Tapered, Flat and Existing Slope with Nailer Versions

Warranty:

The entire roof system is covered under one warranty and inspected after the project is complete to

assure proper installation. The system is inspected after the project is complete to assure proper

installation. This ensures protection for the most vulnerable area of the roof against failure due to

extreme wind up lift pressures.

Testing:

• Tested per ANSI/SPRI ES-1 Standard to comply with the International Building Code.

“ Factory Mutual 1-90 approved for wind up lift protection.

• Miami-Dade Approved (No. 08-0604.02 12/11/13) to comply with the “High Velocity Hurricane

Zone of the Florida Building Code”.

Available Materials:

Its unique design allows for covers to be manufactured in 24 ga. steel, .040", .050" and .063"

aluminum.

Watertight:

Its 8" wide concealed splice plates with dual non-curling isocryl butyl sealant strips allow for thermal

movement of materials and provides a watertight seal at all joints.

Competitively Priced:

The installed cost rivals even light gauge roof edge systems fabricated locally or in a roofer’s shop.

Efficient Design:

A fuU, snap-on design in 12'-0" lengths and no crimping make for quick installation and low labor

costs. Pre-punched fastening holes ensure proper attachment to the building substrate. Corrosion

resistant, stainless steel springs are factory attached to the anchor clips and provide long-term,

positive spring loading. No adhesives are required.

Colors:

Choose among a wide range of standard colors and finishes that meet your job requirements. A 20

year Kynar 500® finish warranty is included on standard colors. Custom post-coated Kynar 500

colors are available with an included 10 year Kynar 500 finish warranty or a 20 year Kynar 500 finish

warranty is available upon request. Anodized finishes are also available, but are not warranted.

Custom Capabilities:

Radius and specially fabricated products are available to meet the unique needs of each project.

Accessories:

Factory fabricated miters provide a cleaner, more aesthetically pleasing appearance. This eliminates

the need for field fabrication, providing time and labor savings.

Also Included:

All fasteners are included and will arrive to the job site with the product.

p: 800-969-0108

f: 610-916-9501

features & benefits

Summary of content (30 pages)

PAGE 1
Flexcap FLC Coping Tapered, Flat and Existing Slope with Nailer Versions Warranty: The entire roof system is covered under one warranty and inspected after the project is complete to assure proper installation. The system is inspected after the project is complete to assure proper installation. This ensures protection for the most vulnerable area of the roof against failure due to extreme wind up lift pressures.
PAGE 2
FLEXCAP FLC COPING TAPERED VERSION APPROVE) ANSI/SPRI ES-1 TESTED Coping cover 12'-0' (3.65 m) lengths 12" (305 mm) wide NOANa-M^ll \Vm) Cwsty, 20 ga. (1 mm) galvanized 8" (203 mm) wide concealed splice plate at each joint anchor clips 4'-0" (1.22 m) o.c. 'C 'A' Outside Face Min. 3" (76 mm) Max. 6" (152 mm) Inside Face Min. 2 1/4" (57 mm) Max.
PAGE 3
FLEXCAP FLC COPING s FLAT VERSION APPROVED ANSI/SPRI ES-1 TESTED Coping cover 12'-0" (3.65 m) lengths NOAK0.WWM Il'IDti 12" (305 mm) wide 8" (203 mm) wide concealed splice plate at each joint 20 ga. (1 mm) galvanized anchor clips 4'-0" (1.22 m) o.c. 15/16" 15/16" (24 mm) (24 mm) "C" 'A' Inside Face Min. 2 1/4" (57 mm) Max. 6" (152 mm) ,1/ Outside Face Min. 3" (76 mm) Max.
PAGE 4
FLEXCAP FLC COPING APPROVH EXISTING SLOPE WITH NAILER VERSION ANSI/SPRI ES-1 TESTED L Coping is to be installed per Specifications and Flex's Installation Instruction Dwg. # 28111-3460 - Concealed splice plates are provided with factory applied dual non- curing sealant strips. - Unless otherwise noted, fabrication of miters and accessories are furnished standard utilizing a non-penetrating quicklock joint, then factory sealed watertight.
PAGE 5
QUICKLOCK MITERS / ACCESSORIES Non-penetrating lock without welding Smooth, neat finished appearance No leak lock 20 year Kynar finish warranty Customer Service Phone: 800-969-0108 Fax:610-916-9501 p: 800-969-0108 f: 610-916-9501 DATE: 12/13/10 SHT.
PAGE 6
FLEXCAP FLC COPING FLAT OR TAPERED MITERS - QUICKLOCK CONSTRUCTION WITH SEALANT OUTSIDE MITER STANDARD OUTSIDE LEG LENGTH: ROOF SIDE WALL SIZE + 9 5/8" = LENGTH INSIDE MITER ROOF SIDE STANDARD INSIDE LEG LENGTH: WALL SIZE + 9 5/8" = LENGTH * TREATED WOOD NAILERS RECOMMENDED ^ CUSTOM ANGLES & SIZES AVAILABLE OUTSIDE FACE Customer Service Phone: 800-969-0108 Fax:610-916-9501 DATE: 12/13/10 SHT.
PAGE 7
FLEXCAP FLC COPING FLAT OR TAPERED MITERS - QUICKLOCK CONSTRUCTION WITH SEALANT "T" MITER (TAPERED SHOWN) ROOF SIDE STRAIGHT TRANSITIONAL MITER (TAPERED SHOWN) TRANSITIONAL MITER (FOR 2 DIFFERENT WALL WIDTHS) (TAPERED SHOWN) NOTE: TREATED WOOD NAILERS RECOMMENDED.
PAGE 8
FLEXCAP FLC COPING MITERS QUICKLOCK MITER ASSEMBLY Customer Service Phone: 800-969-0108 Fax:610-916-9501 DATE: 12/13/10 SHT.
PAGE 9
FLEXCAP FLC COPING MITERS WELDED PRE-FINISHED MITER ASSEMBLY Customer Service Phone: 800-969-0108 Fax:610-916-9501 p: 800-969-0108 f: 610-916-9501 DATE: 12/13/10 DRN BY: JJC CKD BY: SAK SHTJ OF DWG# 28511-3466 c detail 79
PAGE 10
FLEXCAP FLC COPING MITERS WELDED POST-FINISHED MITER ASSEMBLY Customer Service Phone: 800-969-0108 Fax:610-916-9501 DATE: 12/13/10 SHTJ OF DRN BY: JJC CKD BY: SAK DWG# 28511-3468 c detail p: 800-969-0108 80 f: 610-916-9501
PAGE 11
FLEXCAP FLC COPING ENDCAPS QUICKLOCK ENDCAP ASSEMBLY STANDARD ENDCAP LENGTH IS 18’ Customer Service Phone: 800-969-0108 Fax:610-916-9501 p: 800-969-0108 f: 610-916-9501 DATE: 12/13/10 SHT.
PAGE 12
FLEXCAP FLC COPING ENDCAPS WELDED PRE-FINISHED ENDCAP ASSEMBLY detail p: 800-969-0108 82 f: 610-916-9501
PAGE 13
FLEXCAP FLC COPING ENDCAPS WELDED POST-FINISHED ENDCAP ASSEMBLY p: 800-969-0108 f: 610-916-9501 detail 83
PAGE 14
NON 90° ANGLE FOR COPING MEASUREMENT WORKSHEET FOR USE WITHOUT A PROTRACTOR ROOF SIDE PLACE MARK HERE PLACE MARK HERE WALL SIZE ROOF SIDE WALL SIZE 1. CIRCLE APPROPRIATE "ROOF SIDE" TO INDICATE OUTSIDE MITER OR INSIDE MITER. 2. STARTING AT EITHER SIDE OF THE CORNER, MEASURE ALONG THE WALL EDGE A CONVENIENT DIMENSION, SUCH AS 24" OR 36", DEPENDING ON JOB SITE CONDITIONS.
PAGE 15
NON 90° COPING MITERS OUTSIDE MITER-OBTUSE □ Standard Leg Lengths □ Custom Leg Lengths OUTSIDE MITER ACUTE Qty. INSIDE MITER-OBTUSE □ Standard Leg Lengths □ Custom Leg Lengths _ NOTES: Qty. -- Concealed splice plates are provided with factory applied dual non-curing sealant strips. - Unless otherwise noted, fabrication of miters and accessories are furnished standard utilizing a non penetrating quicklock joint, then factory sealed watertight.
PAGE 16
COPING TRANSITION MITERS Standard Leg Lengths □ Standard Leg Lengths □ Custom Leg Lengths _ □ Custom Leg Lengths _ □ NOTES: -- Concealed splice plates are provided with factory applied dual non-curing sealant strips. - Unless otherwise noted, fabrication of miters and accessories are furnished standard utilizing a non-penetrating quicklock joint, then factory sealed watertight. ■ Welded Miters and Accessories Check one □ Required (surcharge) □ Not applicable MATERIAL: __ 24 Ga. (.
PAGE 17
STRAIGHT COPING TRANSITIONS NOTE: Indicate slope by circling appropriate outside face. LEFT TRANSITION RIGHT TRANSITION OUTSIDE FACE OUTSIDE FACE SPECIFY WALL SIZE OUTSIDE FACE SPECIFY WALL SIZE OUTSIDE FACE □ Standard Leg Lengths □ Standard Leg Lengths □ Custom Leg Lengths _ □ Custom Leg Lengths _ NOTES: - Concealed splice plates are provided with factory applied dual non-curing sealant strips.
PAGE 18
OUTSIDE "T" COPING MITERS RIGHT OUTSIDE "T" MITER OUTSIDE FACE SPECIFY WALL SIZE LEFT OUTSIDE "T" MITER SPECIFY WALL SIZE OUTSIDE FACE SPECIFY inside WALL SIZE face INSIDE FACE OUTSIDE FACE SPECIFY WALL SIZE INSIDE FACE INSIDE FACE SPECIFY WALL SIZE OUTSIDE FACE SPECIFY WALL SIZE NOTES: -- Concealed splice plates are provided with factory applied dual non-curing sealant strips.
PAGE 19
INSIDE "T" COPING MITERS RIGHT INSIDE "T" MITER SPECIFY WALL SIZE INSIDE FACE LEFT INSIDE "T" MITER SPECIFY WALL SIZE INSIDE FACE OUTSIDE FACE SPECIFY WALL SIZE OUTSIDE FACE INSIDE FACE SPECIFY OUTSIDE WALL SIZE face SPECIFY WALL SIZE OUTSIDE FACE INSIDE FACE SPECIFY WALL SIZE NOTES; - Concealed splice plates are provided with factory applied dual non-curing sealant strips.
PAGE 20
*7" COPING MITERS OUTSIDE FACE OUTSIDE FACE HEIGHT R.H. QUANTITY, OUTSIDE FACE OUTSIDE FACE HEIGHT LH. QUANTITY.____________ □ STANDARD LEG LENGTHS □ STANDARD LEG LENGTHS □ CUSTOM LEG LENGTHS _ □ CUSTOM LEG LENGTHS _ NOTES: - Welded Miters and Accessories - Concealed splice plates are provided with factory Check one □ Required (surcharge) □ Not applicable applied dual non-curing sealant strips.
PAGE 21
STEP-UP COPING MITERS LEFT HAND STEP-UP MITER SPECIFY RISE DIMENSION RIGHT HAND STEP-UP MITER OUTSIDE FACE SPECIFY RISE DIMENSION \ROOFO DIRECTION IS DETERMINED AS SEEN FROM ROOF NOTES: ^ Concealed splice plates are provided with factory applied dual non-curing sealant strips. - Welded Miters and Accessories Check one □ Required (surcharge) □ Not applicable MATERIALS: __ 24 GA. (.65 mm) Steel __ .040" (1.
PAGE 22
ENDWALL FLASHING SPLICE PLATE VERSION Fabrication will proceed only after receipt of signed print approval. Print Approval: Architect and/or contractor shall verify all dimensions, sizes and quantities. All products to be installed in strict accordance with Flex's printed instructions. MATERIALS: .040" (1.
PAGE 23
ENDWALL FLASHING COPING VERSION 3" Fabrication will proceed only after receipt of signed print approval. Print Approval: Architect and/or contractor shall verify all dimensions, sizes and quantities. All products to be installed in strict accordance with Flex's printed instructions. Approved by; Date: MATERIALS: __ 24 GA. (0.65 mm) Steel _.040" (1.01 mm) Alum. __ .050" (1.27 mm) Alum. __ .063" (1.60 mm) Alum. Other_________________ Finish: QUANTITIES: _______ Right End Flashing .
PAGE 24
FLEXCAP FLC QUICKLOCK RADIUS COPING > Premanufactured radius coping utilizing a non-penetrating lock system. The non-penetrating quicklock joint is then factory sealed watertight. > 2 to 3 week lead time instead of the standard 5 to 6 week lead time for welded post coated radius coping. > No welding required. TYP. 1 1/4 TYP.
PAGE 25
FLEXCAP FLC QUICKLOCK RADIUS COPING TAPERED VERSION IMPORTANT!!! MUST INDICATE PROPER RADIUS CONDITION BY CIRCLING APPROPRIATE OUTSIDE FACE PROVIDING A RADIUS THE RADIUS MAY BE PROVIDED IN ONE OF TWO METHODS: 1.) THE ACTUAL KNOWN RADIUS IS OR 2.) FIELD CONDITION MEASUREMENTS NOTE: REFER TO ATTACHED WORKSHEET MIDPOINT OF STRAIGHT EDGE INSIDE FACE MIN. 2 1/4" (57 mm) MAX. 6" (152 mm) (914 mm) LENGTH OF STRAIGHT EDGE NOTE: CHECK MEASUREMENTS ALONG ENTIRE RADIUS.
PAGE 26
FLEXCAP FLC WELDED RADIUS COPING TAPERED VERSION IMPORTANT!!! MUST INDICATE PROPER RADIUS CONDITION BY CIRCLING APPROPRIATE OUTSIDE FACE PROVIDING A RADIUS OUTSIDE FACE THE RADIUS MAY BE PROVIDED IN ONE OF TWO METHODS: ROOF LINE RADIUS (PROVIDED BY APPROVER PER DETAIL A) 1.) THE ACTUAL KNOWN RADIUS IS OR TOP VIEW 2.) FIELD CONDITION MEASUREMENTS NOTE: REFER TO ATTACHED WORKSHEET WELDED 1 3/8" (35 mm) MIDPOINT OF STRAIGHT EDGE INSIDE FACE MIN. 2 1/4" (57 mm) MAX.
PAGE 27
FLEXCAP FLC QUICKLOCK RADIUS COPING FLAT VERSION IMPORTANT!!! MUST INDICATE PROPER RADIUS CONDITION BY CIRCLING APPROPRIATE OUTSIDE FACE PROVIDING A RADIUS OUTSIDE FACE THE RADIUS MAY BE PROVIDED IN ONE OF TWO METHODS: ROOF LINE RADIUS (PROVIDED BY APPROVER PER DETAIL A) 1.) THE ACTUAL KNOWN RADIUS IS OR TOP VIEW 2.) FIELD CONDITION MEASUREMENTS NOTE: REFER TO ATTACHED WORKSHEET SEALANT MIDPOINT OF STRAIGHT EDGE INSIDE FACE MIN. 2 1/4" (57 mm) MAX.
PAGE 28
FLEXCAP FLC WELDED RADIUS COPING FLAT VERSION IMPORTANT!!! MUST INDICATE PROPER RADIUS CONDITION BY CIRCLING APPROPRIATE OUTSIDE FACE PROVIDING A RADIUS OUTSIDE FACE THE RADIUS MAY BE PROVIDED IN ONE OF TWO METHODS: ROOF LINE RADIUS (PROVIDED BY APPROVER PER DETAIL A) 1.) THE ACTUAL KNOWN RADIUS IS OR TOP VIEW 2.) FIELD CONDITION MEASUREMENTS NOTE: REFER TO ATTACHED WORKSHEET 15/16“ (24 mm) (457 mm) MIDPOINT OF STRAIGHT EDGE 15/16“ I (24 mm) INSIDE FACE MIN. 2 1/4" (57 mm) MAX.
PAGE 29
2 PC COUNTERFLASHING REGLET AND SURFACE VERSION NOTE: PRE-NOTCHED LAP JOINT 3" (76 mm) Fabrication will proceed only after receipt of signed print approval. Print Approval: Architect and/or contractor shall verify all dimensions, sizes and quantities. All products to be installed in strict accordance with Flex's printed instructions. MATERIAL: __ 24 Ga. (.65 mm) Galv. __ .040" (1.01 mm) Alum, __ .050" (1.27 mm) Alum.
PAGE 30
Q. t* m -- O TYPICAL COPING COMPONENTS o o 'lO —* m Oik %o ma o tn —“ o o —^ as Customer Service Phone: 800-969-0108 Fax:610-916-9501 DATE: 12/13/10 SHT.