User's Manual
Table Of Contents
- Content
- Preface
- Introduction
- Notice
- Chapter 1: 3D Printing Technology
- Chapter 2: About GuiderIIS
- Chapter 3：Unpacking
- Chapter 4: Hardware Assembly
- Chapter 5: Build Plate Leveling
- Chapter 6: About Software
- 6.1 Software Installation
- 6.2 Exploring FlashPrint
- 6.2.4 Views
- ①Changing views
- ②Set View
- ③Reset View
- ④Show Model Outline
- ⑤Show Steep Overhang
- 6.2.5 Move
- 6.2.6 Rotate
- 6.2.7 Scale
- 6.2.8 Cut
- 6.2.9 Supports
- ②Auto Supports
- ③Add Supports
- ④ Clear Supports
- Click [Clear Supports], all supports will be delet
- ⑤Delete Supports
- 6.2.10 Print
- 6.2.11 File Menus
- 6.2.12 Edit Menus
- 6.2.13 Print Menus
- 6.2.14 Tool Menus
- ① Control Panel
- ② Update Firmware
- NOTE！Please update firmware under instructions of
- ③ On Board Preferences
- ④ Machine information
- 6.2.15 Help Menus
- Chapter 7: Basic Printing
- Chapter 8: Supports and Service
- Chapter 9:Basic Questions and Answers
- Note! Do not disassemble the printer for maintenan
- 9.1 Extruder shakes from left and right when print
- 9.2 “1025” extruder temperature showed on printer’
- Step 1. Extruder thermocouple has loose contact or
- 9.9 Wave-like lines appear on the surface of model
- 1. Apply some lubricate grease on the Z-Axis.
- 2. Z-Axis guide rods and Z-Axis bearings do not co
- 9.10（1）One of the axis motor is not working or rot
- 9.12 Files sliced by Flashprint and transferred by
- 9.13 Print results shift along the direction of X-
- 9.14 When doing build plate leveling, touch screen
GuiderIIS User Guide | www.flashforge.com 400-699-1063
sensor wire, if problem remains, replace with new X-Axis sensor wire.
Step 2. If Step1 not solving, trigger iron piece of the X-Axis sensor has dropped off or
has problem: Replace with new X-Axis sensor.
9.5 Print result is ellipse when we set to print perfect
roundness, and print result is rhombus when we set to print
rectangle.
Step 1. X-Axis is not vertical to Y-Axis: Check the verticality between X-Axis and
Y-Axis，adjust the X-Axis vertical to the Y-Axis.
9.6 Filament can not come out from extruder when printing
the first layer and extruder is rubbing the platform.
Step 1. Distance between extruder and platform is too small: Re-do the build plate
leveling according to Chapter 5.
9.7 Extruder is clogged, filament is jammed in the metal
throat tube or teflon tube.
Step 1. Clear and unclog the extruder.
Referring operating video: FLASHFORGE GuiderIIS Unclogging Extruder
https://www.youtube.com/watch?v=ePZgmtLxLZU&t=22s
9.8(1) Extruder motor rotates normally but filament comes
out from extruder not continuously(off and on).
(2)Extruder motor rotates normally but filament does not
come out from extruder, and new filament can not be loaded
into extruder or squeezed out.
1.Other brands filament is used in printer,inferior filament has impurities or bubbles
inside: Please use Flashforge filament and make sure filament be stored at clean and