User's Manual
Table Of Contents
- Content
- Preface
- Introduction
- Notice
- Chapter 1: 3D Printing Technology
- Chapter 2: About GuiderIIS
- Chapter 3：Unpacking
- Chapter 4: Hardware Assembly
- Chapter 5: Build Plate Leveling
- Chapter 6: About Software
- 6.1 Software Installation
- 6.2 Exploring FlashPrint
- 6.2.4 Views
- ①Changing views
- ②Set View
- ③Reset View
- ④Show Model Outline
- ⑤Show Steep Overhang
- 6.2.5 Move
- 6.2.6 Rotate
- 6.2.7 Scale
- 6.2.8 Cut
- 6.2.9 Supports
- ②Auto Supports
- ③Add Supports
- ④ Clear Supports
- Click [Clear Supports], all supports will be delet
- ⑤Delete Supports
- 6.2.10 Print
- 6.2.11 File Menus
- 6.2.12 Edit Menus
- 6.2.13 Print Menus
- 6.2.14 Tool Menus
- ① Control Panel
- ② Update Firmware
- NOTE！Please update firmware under instructions of
- ③ On Board Preferences
- ④ Machine information
- 6.2.15 Help Menus
- Chapter 7: Basic Printing
- Chapter 8: Supports and Service
- Chapter 9:Basic Questions and Answers
- Note! Do not disassemble the printer for maintenan
- 9.1 Extruder shakes from left and right when print
- 9.2 “1025” extruder temperature showed on printer’
- Step 1. Extruder thermocouple has loose contact or
- 9.9 Wave-like lines appear on the surface of model
- 1. Apply some lubricate grease on the Z-Axis.
- 2. Z-Axis guide rods and Z-Axis bearings do not co
- 9.10（1）One of the axis motor is not working or rot
- 9.12 Files sliced by Flashprint and transferred by
- 9.13 Print results shift along the direction of X-
- 9.14 When doing build plate leveling, touch screen
GuiderIIS User Guide | www.flashforge.com 400-699-1063
motor to be controlled manually.
● LED Color: Allow users to change the LED color of GuiderIIS.
● Extruder Controls: You can set the value of “Motor Speed (RPM)”, which can
control the rotation speed of filament feeding wheel. The motor rotation time can be
controlled via setting the value of “Extruder Duration”. Generally we suggest the
users choose option of continuous time 60 seconds. The filament must be loaded in the
extruder before motor starts. Therefore, do not start rotation operation until the
extruder temperature reaches to the printing temperature of filament. For PLA
filament, the extruder temperature should reach 200℃, after reaching the extruder
temperature, click the [Forward]/[Reverse] rotation button to control filament load
and filament unload. Furthermore, if you want to stop filament load and unload, you
can click [Stop].
● Temperature Control: Input the temperature you want to get in the left frame, click
[Apply], the printer will automatically heat the corresponding part, the right side
shows the current actual temperature of corresponding part. After starting heating, the
below curve of temperature form will start to change, different color correspond
different parts’ temperatures
② Update Firmware
NOTE！Please update firmware under instructions of Flashforge engineer, Do not
recommend updating on your own.
Every time when you start FlashPrint, it will automatically detect and download the
up-to-date firmware. If any update is available, a dialog box will pop up for reminding
the users to update.
Step 1: Click [Tools]--[Update firmware]. It needs to cut off connection before
updating firmware. If software and printer are already in connection, it reminds you
cutting off the connection, and then choose [Yes] and go on to the next step.