User's Manual
Table Of Contents
- Content
- Preface
- Introduction
- Notice
- Chapter 1: 3D Printing Technology
- Chapter 2: About GuiderIIS
- Chapter 3:Unpacking
- Chapter 4: Hardware Assembly
- Chapter 5: Build Plate Leveling
- Chapter 6: About Software
- 6.1 Software Installation
- 6.2 Exploring FlashPrint
- 6.2.4 Views
- ①Changing views
- ②Set View
- ③Reset View
- ④Show Model Outline
- ⑤Show Steep Overhang
- 6.2.5 Move
- 6.2.6 Rotate
- 6.2.7 Scale
- 6.2.8 Cut
- 6.2.9 Supports
- ②Auto Supports
- ③Add Supports
- ④ Clear Supports
- Click [Clear Supports], all supports will be delet
- ⑤Delete Supports
- 6.2.10 Print
- 6.2.11 File Menus
- 6.2.12 Edit Menus
- 6.2.13 Print Menus
- 6.2.14 Tool Menus
- ① Control Panel
- ② Update Firmware
- NOTE!Please update firmware under instructions of
- ③ On Board Preferences
- ④ Machine information
- 6.2.15 Help Menus
- Chapter 7: Basic Printing
- Chapter 8: Supports and Service
- Chapter 9:Basic Questions and Answers
- Note! Do not disassemble the printer for maintenan
- 9.1 Extruder shakes from left and right when print
- 9.2 “1025” extruder temperature showed on printer’
- Step 1. Extruder thermocouple has loose contact or
- 9.9 Wave-like lines appear on the surface of model
- 1. Apply some lubricate grease on the Z-Axis.
- 2. Z-Axis guide rods and Z-Axis bearings do not co
- 9.10(1)One of the axis motor is not working or rot
- 9.12 Files sliced by Flashprint and transferred by
- 9.13 Print results shift along the direction of X-
- 9.14 When doing build plate leveling, touch screen
GuiderIIS User Guide | www.flashforge.com 400-699-1063
⑤
Show Steep Overhang
Click [View]--[Show Steep Overhang]. When the intersection angle between the
model surface and horizontal line is within the overhang threshold value, the surface
has steep overhang and it becomes red in the software. Overhang threshold value
could be set as needed. The default value is 45 degree.
6.2.5 Move
Select the object and move the object by the following two methods:
Method 1: Click the [Move] icon on the left, hold down the left mouse button and
drag to adjust the location of the model in XY direction. Hold down the Shift key,
hold down the left mouse button and drag to adjust the location of the model in Z
direction. The distance and the direction of the movement shall be displayed.
Method 2: Click the [Move] button on the left and then enter the distance value. Click
[Reset] to reset distance values.
Note: Users shall click [Center] and [On Platform] after the location adjustment to
ensure the model(s) be within the build area and on the build platform. If a specified
position is needed, only click [On Platform].
6.2.6 Rotate
Select the target object and rotate the object by the following two methods:
Method 1: Click the [Rotate] icon on the left and three mutually perpendicular rings
appear around the object Click one ring and rotate on the present axis, you will see the
rotation angle and direction in the center of circle. In this way, you could make the
model rotate on X/Y/Z axis.
Method 2: Click the [Rotate] icon on the left, and then enter into rotating angel
values in X/Y/Z axes positioning. Click [Reset] to reset rotating angel values.