Quick Start Guide

ManualsBrandsFlashForge ManualsDigital PhotographyAdventurer 3 3D Printer

本手册仅适用于闪铸科技 Adventurer3 3D打印机

This guide is only applicable to FLASHFORGE Adventurer3 3D printer

快速启动指南

ADVENTURER 3 / 冒险家 3

Quick Start Guide

中文P11

SZ16-ZN/EN-A05

Summary of content (12 pages)

PAGE 1
SZ16-ZN/EN-A05 ADVENTURER 3 / 冒险家 3 Quick Start Guide 快速启动指南中文P11 This guide is only applicable to FLASHFORGE Adventurer3 3D printer 本手册仅适用于闪铸科技 Adventurer3 3D打印机
PAGE 2
PAGE 3
Unpacking 1 . Open the box. 2. Remove wrapping paper box on the top, there is a Quick start, an after-sales service, an accessory kit, a power cable and a roll of material on the plastic box. 3 . Take out the printer of the carton, remove bubble pack outside the printer. 4 . Tear off fixed tapes and front door protective bag. 5. Take power cable out and plug it into power input. 6. Plug the other end of power cable into socket, turn on the power switch.
PAGE 4
7. Turn on the power switch. 8. Open the front door. Build Network Preheat Status Language Calibration Home Tools Setting About Filament Move Camera FilamentCheck Led < 2/3 < 1/3 < 9. Tap [Tools]-[Setting] on the touch screen as the picture showed above, tap [Move].
PAGE 5
X: 20.00 Y: 45.00 Z: 36.00 Y Z X 10. Tap the upper arrow in the moving page to make the extruder raises for removing the paper box on the bottom easier. 11. Squeeze wrapping paper box to the middle slighly and take it out. 12. Unboxing completed! Recommended that you take good care of packing materials for furthur carrying and keeping.
PAGE 6
Kit Contents 3D Printer Filament Power Cable After-sales service card Screwdriver Unclogging Pin Tool Allen Wrench SZ16-ZN/EN-A01 ADVENTURER 3 发明家 3 快速启动指南 9 1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触! 2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。 1. Hot! Avoid touching the heating nozzle and heating build plate in operation. 2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation. 最新版本说明书请前往闪铸科技官方网站www.sz3dp.
PAGE 7
Getting to know your Adventurer 3 6 1 7 2 23 3 8 4 22 9 5 10 21 20 19 18 11 17 12 16 13 14 24 15 25 26 1. Filament guide tube 2. Filament guide tube joint 3. Extruder base 4.Cooling Fan 5. Removable nozzle 6. Extruder cables 7. Clip 8. Led light 9. Turbo Fan Baffle 10. Front door 11.Y-Axis sliding slot 12.Platform base 13. Removable build plate 14.Touch-screen 15.USB stick input 16.Power switch 17. Power input 18. Spool holder 19.Filament cover 20. Filament cover handle 21. Moto 22.
PAGE 8
First Print 200 /235℃ Build Load Heating extruder... Tools Change Filament Cancel 1. Tap [Filament], tap [Load], after load completed, tap [OK]. 235 /235℃ Preheat completed, Begin loading... 2. As shown on the left, loading starts when the extruder heated to target temperature. 3. Open the filament cover, insert the filament into the filament intake, push filament into the feeding wheel until some resistance is sensed.
PAGE 9
Mind the loading direction of filament, make sure to be clockwise as the picture showed. 235 /235℃ Press ok when new color appears 4. Load completed when you see filament come out of extruder, tap [OK]. Put the spool of filament on the spool holder, close the filament cover.
PAGE 10
Model Print Build 6.67GB Not Available Tools No job Filament 1. Tap [Build], choose the file path: Print from local memory card. 20mm_BoxPLA.gx < 1/3 < 2. Locate the model file in the model list, Tap on its right to start printing; or tap model file picture or file name to enter model details page, tap to start printing. 20mm_Box-P... 0 h 10 min 0.70M 7.49 m Build completed! 20mm_Box-PLA.gx 0 10 h ok min Time Remaining ... 3 .
PAGE 11
Model Remove 1 . As showed in picture, press down dotted line area and draw out the removable build plate. Notices When printing completed, extruder and build plate may still hot, please start operating after cooling down! 2 . Bend the build plate, the plate will produce certain deformation, seperating the plate away from the bottom of model (Please use a scraper to assist removing when model is too small or big).
PAGE 12
Change Filament 200 /235℃ Load Heating extruder... Change Cancel 1 . Tap [Filament], tap [Change], extruder starts preheating. 3 . Pull out the filament as the picture showed above. 4 . Insert new filament into the filament intake and push the filament into the feeding wheel until resistance is sensed. 235 /235℃ Pull out filament, feed new filament, press [OK] 2 . Open the filament cover. 235 /235℃ Press ok when new color appears OK OK 5 . Tap [ok] after plugging in new filament, loading starts.