Product Manual

MANUFACTURING INC.
417-723-5724
104 INDUSTRIAL DRIVE - CRANE, MO
November 2003
INSTALLATION AND OPERATION INSTRUCTIONS
FOR ALL FIVE STAR RAMPS
Thank you for purchasing this set of ramps from Five Star Manufacturing.
Safety is our first concern, and by following the guidelines and installation
procedures your ramps will provide years of dependable, trouble free operation.
1. Remove the ramps from the banding and cardboard protection. Inside you will find a bag containing two sets of web straps.
2. Take one ramp and stand on end against a wall with the tailgate tips facing upwards. Take the looped end of the web strap
a
nd feed it through the third or fourth cross bar of the ramp from the top. Feed the hooked end of the web strap into the loop,
pulling the web assembly through and around the cross rung and center bar and pull tight.
3. Repeat step two for the other ramp, making sure the loops are tight and loomed properly. For BI-FOLD & TRI-FOLD
ramps, install the web straps per the pictures below and follow the instructions 4 through 7.
4. Now place the ramps on the tailgate of the vehicle you are to use the ramps with. Male sure that they are placed against the
edge of the tailgate, with the Red tabs resting firmly on the top of the tailgate. Be sure to place the ramps the correct space for
the wheel width of the vehicle you are loading.
5. Take the web strap with the hook end and secure it to the bottom of the bumper, take the loose end of the web and pull until
the web strap is snug with the ramp and bumper. Be sure to not over tighten the strap, as it will make the ramp move inward or
outward if the strap is not inline with the bumper. If the truck is equipped with a tow package, place the hook ends into the chain
eyelets on either side of the tube receiver and tighten as an alternative.
6. To release the safety straps, push down on the center tab of the binder and pull back, this will release the hook from the
bumper.
7. To store the ramps, stack together and loop one of the hooks through the other and tighten. Take the other ramps web strap
and do the same for that ramp. This will keep them secure while moving or storing ramps.
ALWAYS USE THE WEB STRAPS WHEN LOADING OR UNLOADING VEHICLES.
Check the strap periodically to ensure they are secured to the rungs,
that slippage has not occurred and for any wear and tear that may occur.
For more information on this or
other fine Five Star MFG. products,
or for the name and telephone num-
ber of the dealer nearest you,
please call:
800-733-5720
Website:
www.fivestarmfginc.com
PLEASE READ
NEW PHOTO HERE
NEW PHOTO HERE
NEW PHOTO HERE
MANUFACTURING INC.
417-723-5724
104 INDUSTRIAL DRIVE - CRANE, MO
November 2003
INS TAL LATION AND OPER ATION INSTRUCTIONS
FOR ALL FIVE S TAR RAMPS
Thank you for purchasing this set of ramps from Five Star Manufacturing.
Safety is our first concern, and by following the guidelines and installation
procedures your ramps will provide years of dependable, trouble free operation.
1. Remove the ramps from the banding and cardboard protection. Inside you will find a bag containing two sets of web straps.
2. Take one ramp and stand on end against a wall with the tailgate tips facing upwards. Take the looped end of the web strap
a
nd feed it through the third or fourth cross bar of the ramp from the top. Feed the hooked end of the web strap into the loop,
pulling the web assembly through and around the cross rung and center bar and pull tight.
3. Repeat step two for the other ramp, making sure the loops are tight and loomed properly. For BI-FOLD & TRI-FOLD
ramps, install the web straps per the pictures below and follow the instructions 4 through 7.
4. Now place the ramps on the tailgate of the vehicle you are to use the ramps with. Make sure that they are placed against the
edge of the tailgate, with the Red tabs resting firmly on the top of the tailgate. Be sure to place the ramps the correct space for
the wheel width of the vehicle you are loading.
5. Take the web strap with the hook end and secure it to the bottom of the bumper, take the loose end of the web and pull until
the web strap is snug with the ramp and bumper. Be sure to not over tighten the strap, as it will make the ramp move inward or
outward if the strap is not inline with the bumper. If the truck is equipped with a tow package, place the hook ends into the chain
eyelets on either side of the tube receiver and tighten as an alternative.
6. To release the safety straps, push down on the center tab of the binder and pull back, this will release the hook from the
bumper.
7. To store the ramps, stack together and loop one of the hooks through the other and tighten. Take the other ramp’s web strap
and do the same for that ramp. This will keep them secure while moving or storing ramps.
ALWAYS USE THE WEB STRAPS WHEN LOADING OR UNLOADING VEHICLES.
Check the strap periodically to ensure they are secured to the rungs,
that slippage has not occurred and for any wear and tear that may occu r.
For more information on this or
other fine Five S tar MFG. products,
or for the name and telephone num -
ber of the dealer nearest you,
please call:
800-733-5720
Website:
www.fivestarmfginc.com
PLEASE READ
NEW PHOTO HERE
NEW PHOTO HERE
NEW PHOTO HERE
MANUFACTURING INC.
417-723-5724
104 INDUSTRIAL DRIVE - CRANE, MO
November 2003
INS TAL LATION AND OPER ATION INSTRUCTIONS
FOR ALL FIVE S TAR RAMPS
Thank you for purchasing this set of ramps from Five Star Manufacturing.
Safety is our first concern, and by following the guidelines and installation
procedures your ramps will provide years of dependable, trouble free operation.
1. Remove the ramps from the banding and cardboard protection. Inside you will find a bag containing two sets of web straps.
2. Take one ramp and stand on end against a wall with the tailgate tips facing upwards. Take the looped end of the web strap
and feed it through the third or fourth cross bar of the ramp from the top. Feed the hooked end of the web strap into the loop,
pulling the web assembly through and around the cross rung and center bar and pull tight.
3. Repeat step two for the other ramp, making sure the loops are tight and loomed properly. For BI-FOLD & TRI-FOLD
ramps, install the web straps per the pictures below and follow the instructions 4 through 7.
4. Now place the ramps on the tailgate of the vehicle you are to use the ramps with. Make sure that they are placed against the
edge of the tailgate, with the Red tabs resting firmly on the top of the tailgate. Be sure to place the ramps the correct space for
the wheel width of the vehicle you are loading.
5. Take the web strap with the hook end and secure it to the bottom of the bumper, take the loose end of the web and pull until
the web strap is snug with the ramp and bumper. Be sure to not over tighten the strap, as it will make the ramp move inward or
outward if the strap is not inline with the bumper. If the truck is equipped with a tow package, place the hook ends into the chain
eyelets on either side of the tube receiver and tighten as an alternative.
6. To release the safety straps, push down on the center tab of the binder and pull back, this will release the hook from the
bumper.
7. To store the ramps, stack together and loop one of the hooks through the other and tighten. Take the other ramp’s web strap
and do the same for that ramp. This will keep them secure while moving or storing ramps.
ALWAYS USE THE WEB STRAPS WHEN LOADING OR UNLOADING VEHICLES.
Check the strap periodically to ensure they are secured to the rungs,
that slippage has not occurred and for any wear and tear that may occu r.
For more information on this or
other fine Five S tar MFG. products,
or for the name and telephone num -
ber of the dealer nearest you,
please call:
800-733-5720
Website:
www.fivestarmfginc.com
PLEASE READ
NEW PHOTO HERE
NEW PHOTO HERE
NEW PHOTO HERE
#1 MFG. OF ALUMINUM RAMPS IN THE USA
#1 MFG. OF ALUMINUM RAMPS IN THE USA
Ramps
with
angle ends
DO NOT
require
safety straps.