Product features and decorations may vary from picture above. Instructions Model Number: H4792 WARNING IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Please read these instructions before use of this product. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). Requires four LR20 ("D") alkaline batteries (not included) for operation. www.fisher-price.
Parts WARNING IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. To prevent serious injury or death from falls and being strangled in the restraint system: • Always use the restraint system. Never rely on the tray to restrain child. • Never use with an active child who may be able to climb out of the seat. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg (20 lbs).
Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Hubs CAUTION This package contains small parts in its unassembled state. Adult assembly is required. Housing Leg Back Base Button 2 Front Curved Base • Place the front curved base on a flat surface so that it curves away from you.
Assembly CORRECT INCORRECT HUBS FACING OUT HUBS FACING IN FRONT BASE CURVES INWARD FRONT BASE CURVES OUT 3 • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above. • If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat assembly step 2. • Set the frame assembly aside.
Assembly Armrest Holes Oval End Seat Tube Round End Seat Tube 4 Seat Bottom Round 6 • Position the seat bottom so that the back faces you and the armrest holes are facing up. • Locate the round end seat tube. Hint: Look at opening in the straight end of the tube. It should be completely round. • Fit the round end seat tube into the round hole in the seat bottom. Oval • Locate the oval end seat tube. Hint: Look at opening in the straight end of the tube. It should be oval.
Assembly Seat Back Raised Slots Seat Back Wire Seat Bottom 8 • Fit the seat back to the seat bottom. #8 x 1.9 cm Screw 10 • Fit the seat back wire through the raised slots on the seat back. Rod 9 • Insert the rod into the side opening between the seat back and seat bottom. • Insert a #8 x 1.9 cm screw into the opening in the rod and tighten. 11 • Fit the ends of the seat back wire into the outside holes in the seat tubes.
Assembly Hubs Seat Tubes Assembly Tool 13 • Insert the ends of the seat tubes into the holes in the hubs. • Push the seat tubes in until you hear a “snap” (for each). • Push down on the seat to be sure the seat is secured in both frame hubs. Rounded Side 12 Lock Nut – 2 • Attach a lock nut, rounded side facing out, onto one end of a seat back wire. • Tighten the lock nut by using the assembly tool. Turn the tool clockwise to tighten the lock nut.
Assembly Elastic Loops 16 Waist Belts Holes • Insert the waist belts through the slots in the pad. • Fit the top of the pad over the seat back edge. Elastic Loops Tabs 15 • Place the pad onto the seat. • Insert the pad elastic loops through the holes in the seat bottom. • From under the seat, fit the elastic loops onto the tabs on the seat back. 17 Tabs • From behind the seat, fit the pad elastic loops to the tabs on the seat back.
Assembly Slot #8 x 1.9 cm Screw – 2 Toy Bar Hubs Crotch Belt 19 Clips Seat Tubes • Fit the toybar hubs to the seat tubes. Hint: The toybar hubs are designed to fit to the seat tubes one way. If the toybar hubs do not fit correctly, turn the toybar around and try again. • Insert a #8 x 1.9 cm screw through the seat tubes and into the toybar hubs. Tighten the screws. 18 Elastic Loops • Fit the crotch belt through the slot in the pad. • Fit the pad side clips around the edge of the seat bottom.
Assembly Tray Tray Links 20 • Fit and “snap” the tray onto the seat armrests. • Insert and “snap” the tray links into the holes in the tray. 21 • Fit the toy links and/or toys on the toy bar/tray! Assembly is now complete.
Battery Installation Hint: We recommend using alkaline batteries for longer battery life. 1,5V x 4 “D” (LR20) Shown Actual Size Battery Safety Information Batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment.
Setup and Use IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. WARNING Waist Belts To prevent serious injury or death from falls and being strangled in the restraint system: • Always use the restraint system. Never rely on the tray to restrain child.
Setup and Use Music Button Power Switch Seat Wire 4 3 Swinging • Make sure your child is properly secured in the seat. • Slide the swing power switch on to any of six speed settings. • Watch the toys move when the seat swings! • Be sure to slide the switch to the off position when the swing is not in use. Hint: As with most battery-powered swings, a heavier child will reduce the amount of swinging motion on all settings.
Setup and Use Care • The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Line dry only. •The frame, links, toys and toy bar may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Toy Bar Elastic Loops 1 To remove the pad: • Remove the four pad elastic loops from the seat back and bottom tabs. • Remove the top of the pad from the seat.
Storage Consumer Information GREAT BRITAIN Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500302. AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. ASIA Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. MALAYSIA Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. ©2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
