Installation Guide

36
IMPORTANT!
●
The standard appliance includes a stainless steel toe kick 4 (102mm) and the components required to mount the toe kick.
●
Alternatively, the customer can supply their own custom toe kick 4–6 (102–152mm) for complete integration of the appliance.
For custom toe kick greater than 4" (102mm)
5
Remove the bottom grille from the bottom of the appliance.
6
Measure the required height for the bottom grille.
On a board, carefully score / cut theexcess vanes from
thebottom of the toe kick grille and discard (E).
7
Drill Ø 5/32 (4mm) holes into the dimples of the grille (F).
9
Align the air flow divider underneath the grille tabs
indicator and clip onto the vanes of the bottom grille (H).
For standard toe kick — 4" (102mm)
1
Loosen the toe kick bracket screws (A) mid-way, and move
the brackets forward (B).
4
Align the air flow divider underneath the grille tabs indicator
and clip onto the vanes of the bottom grille (D).
A
B
C
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
D
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
H
8
With the grille tabs facing upwards, align the grille to
the bottom of the plinth where the screw holes are
located and secure with #8x16 pan head screws (G).
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
Grille tabs
DETAIL B
SCALE 2 : 5
G
Front right view
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
E
Cut excess vanes from the bottom of the grille
F
2
Pre-align the toe kick by placing in front of the brackets until flush
with surrounding cabinetry. Once satisfied with the alignment,
set the toe kick aside and tighten the bracket screws to lock the
brackets in position.
3
Peel off the adhesive backing from one side of dual adhesive tabs
and attach to the brackets. Peel off the adhesive backing from the
other side of dual adhesive tabs and attach the toe kick (C).
Internal box
E
Door/drawer
trim install kit
Dual adhesive tabs
(2)
Z
Miscellaneous
components
#8 x 5/8 Pan Head Philips Screw
#8 x 5/8 Pan Head Philips Screw
#8x16 panhead screw (3)
Miscellaneous
itemspack
Air flow divider
(1)
External box
Toe kick
(1)
Tools
Cutter
Cross-head screwdriver
TOE KICK INSTALLATION