INSTALLATION INSTRUCTIONS Framed cabinetry ActiveSmart™ Built-in refrigerator RS36A80J and RS36A80U models US CA www.fisherpaykel.com 843155 B 08.
FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY NOTE: PRODUCT IS DESIGNED FOR FLUSH INSET INSTALLATION ONLY RS36A80J and RS36A80U models FRAMELESS CABINETRY (Frameless: Aligns the product with the cabinetry) FRAMED CABINETRY (Framed: Aligns the product with the frame of the cabinetry) Note: shown with custom panel attached to fridge Note: shown with custom panel attached to fridge (refer to the flip side of the booklet) 1 SAFETY AND WARNINGS 2 BEFORE INSTALLATION 3 COMPONENTS LIST 4 MAXIMU
1 2 SAFETY AND WARNINGS ! Please follow the installation steps below to ensure your appliance is installed and operates correctly. WARNING! Electric Shock Hazard Read and follow the safety and warnings outlined in this installation instructions guide before operating this appliance. Failure to do so can result in death, electric shock, fire or injury to persons. Power ●● ●● ●● ! WARNING! Cut Hazard Take care – panel edges are sharp. Failure to use caution could result in injury or cuts.
3 COMPONENTS LIST Door panel fittings – Included with standard appliance. French door hanging bracket (2) Drawer hanging bracket (1) Side bracket (10) Side strap (10) M5 x 10 pan head Phillips screw (10) M8 stud (6) M8 washer (6) M8 nut (6) Top cover (4) Side cover (10) Anti-tip bracket fittings – Included with standard appliance.
3 COMPONENTS LIST Optional accessories – The standard appliance does not include a door panel set. Fisher & Paykel door panel sets are available (EZKleen stainless steel door panels). To complete the integrated appliance for non-Water dispensing models the customer should supply their own custom door panel set.
3 COMPONENTS LIST Product hardware – Included with standard appliance.
4 MAXIMUM DISTANCE OF HOSE AND POWER CORD Power cord (excl. plug) – 31 1/2” (800 mm) LEFT HAND SIDE Water inlet hose – 53” (1350 mm) Power cord (excl. plug) – 80 3/4” (2051 mm) RIGHT HAND SIDE Water inlet hose – 84 1/4” (2120 mm) Power cord (excl.
F F 5 PRODUCT AND CAVITY DIMENSIONS J J F F G G F F B 3 1/2” (89 mm) A A D D B C 5/32” (4 mm) A A Framed: Finished return top and sides Note: shown with custom panel attached to fridge C F Flush with front of cabinetry PLAN VIEW F E E B B I I F H H F C C F PRODUCT DIMENSIONS inches (mm) D Overall height of product* FRONT VIEW F PROFILE VIEW 79 27/32” (2028) E Overall width of product 35 1/32” (890) F Minimum cabinetry gap clearance from edge of custom panels** CAVITY DIMENSI
5 PRODUCT AND CAVITY DIMENSIONS Z C D B A B For 90° door swing a hinge limiting pin is supplied with your appliance. This pin fits in the boreholes of the top hinge (refer to Z). A WARNING! 115° DOOR OPENING (FULL ROTATION) Before opening doors to the product, ensure the product is on its base packer and the polystyrene stability blocks are still in place. Failure to follow these instructions could lead to serious injury or death. 90° DOOR OPENING Wall Wall 1 Open door to 90°.
FF 5 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680 DOOR PANEL SET FF LL GG FF B KK AA 3 1/2” (89 mm) AA DD B C Flush with front of cabinetry 5/32” (4 mm) C Framed: Finished return top and sides F PLAN VIEW JJ F EE II E Overall width of product CC inches (mm) F27/32” (2028) 79 D Overall height of product* BB F F PRODUCT DIMENSIONS HH F 35 21/32” (906) F Minimum cabinetry gap clearance from edge of product FRONT VIEW PROFILE VIEW CAVITY DIMENSIONS inches (mm) A Overall height
FF 5 FF PRODUCT AND CAVITY DIMENSIONS – WITH RD3684 DOOR PANEL SET LL FF GG B B KK AA 3 1/2” (89 mm) AA DD 5/32” (4 mm) Framed: Finished return top and sides C C F JJ Flush with front of cabinetry PLAN VIEW F F F EE II PRODUCT DIMENSIONS HH D BB CC F F inches (mm) Overall height of product* 83 27/32” (2130) E Overall width of product 35 21/32” (906) F Minimum cabinetry gap clearance from edge of product FRONT VIEW PROFILE VIEW 5/32” (4) G Overall depth of product (excluding
5 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680/RD3684 DOOR PANEL SET Z D E B C A B C For 90° door swing a hinge limiting pin is supplied with your appliance. This pin fits in the boreholes of the top hinge (refer to Z). A WARNING! 115° DOOR OPENING (FULL ROTATION) Wall 90° DOOR OPENING Before opening doors to the product, ensure the product is on its base packer and the polystyrene stability blocks are still in place. Failure to follow these instructions could lead to serious injury or death.
6 CAVITY PREPARATIONS B Left side of cavity Alternative area above cavity for electrical connections 29 3/4” (756 mm) C 5 ⅝” (143 mm) Floor 2” (51 mm) 2 7/8” (73 mm) Electrical and water connections must be within this space if located behind the refrigerator REAR OF CAVITY A IMPORTANT! For ease of installation, ensure cavity width is consistent top to bottom and height is consistent left to right.
7 B CUSTOM DOOR PANEL DIMENSIONS Note: top trim supplied for 84” (2134 mm) installation C A A B g C A A g E D g I D PROFILE VIEW RS36A80J F DIMENSIONS g inches (mm) D panel A Height of top door min. 45 9/32 – max. 49 9/32” (min. 1150 – max.
7 CUSTOM DOOR PANEL DIMENSIONS The drawings below apply to non-Water dispensing models only (RS36A80J). Dimensions are shown in Imperial (inches) and apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on http://thekitchentools.fisherpaykel.com 15 7/16 2 5/32 Ø 3/32 REF 12x Pilot holes recommended for bracket attachment. (Do not penetrate front surface).
8 80” (2032 mm) CAVITY – ATTACH ANTI-TIP BRACKET IMPORTANT! Safety requires refrigerators be stable when doors and/or drawer, are open. The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 220.5 pound (100 kg) load. This will prevent the possibility of the appliance tipping forward, when doors and/or drawer, are open. WARNING! Failure to follow instructions can lead to serious injury or death.
8 84” (2134 mm) CAVITY – ATTACH ANTI-TIP BRACKET IMPORTANT! Safety requires refrigerators be stable when doors and/or drawer, are open. The anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand a 220.5 pound (100 kg) load. This will prevent the possibility of the appliance tipping forward, when doors and/or drawer, are open. WARNING! Failure to follow instructions can lead to serious injury or death.
8 84” (2134 mm) CAVITY – ATTACH TOP TRIM WARNING! Take care when working with the appliance outside of the finished enclosure, as the appliance is not secured and has the possibility of tipping forward. Tipping of appliance can lead to serious injury or death. 1 Ensure all external packaging material is removed from the appliance before installation. ~ 13 ”( 33 0 mm ) ~ 13 ”( 33 0 mm ) A 2 4 On the right side of the top trim, insert M5 nuts x2 onto the top and bottom slide.
9 ATTACH SIDE BASE BRACKETS AND DOOR STUDS WARNING! Take care when working with the appliance outside of the finished enclosure, as the appliance is not secured and has the possibility of tipping forward. Tipping of appliance can lead to serious injury or death. 1 Ensure all external packaging material is removed from the appliance before installation.
!0 CONNECT TO WATER AND ELECTRICAL SUPPLY IMPORTANT! ●● ●● ●● ●● ●● ●● ●● ●● ●● 1 The water connection instructions below are intended only for the professional installer. DO NOT use with water that is microbiologically unsafe or of unknown quality. WARNING – connect to potable drinkable water supply only. DO NOT install on line pressure above 120 psi (827 kPa) or below 22 psi (150 kPa). DO NOT use on hot water supply (100°F [38°C max.]). AVOID contamination of pipes during installation.
!0 5 CONNECT TO WATER AND ELECTRICAL SUPPLY Thread the free end of the water hose into the dedicated hole located in the base of the appliance, through to the back of the appliance (refer to C). 7 At the back of your appliance, connect the appliance to the electrical supply (115 VAC, 60 Hz) with the fitted plug and lead, and turn on. Ensure the appliance is connected to its own isolating switch (refer to E). 2 3/8” min.
Add ruler to show flushness x 4? !1 PRE-ALIGNING YOUR PRODUCT IMPORTANT! ●● ●● ●● ●● 1 It is important that the doors are in line with the frame and the appliance is centred before following these steps. It is important that all four corners of the appliance is supported firmly onto the floor to eliminate any movement. Installing the appliance on a soft, uneven, or not level floor may result in twisting of the product and poor door sealing.
!2 INSTALL WATER FILTER CARTRIDGE AND KICKSTRIPS IMPORTANT! ●● ●● 1 The water filter head must be firmly pushed into the product and secured, incorrect installation can lead to water leaks. It is not necessary to shut off the water supply when installing the water filter.
!3 ASSEMBLE DOOR PANEL SET The assembly of Fisher & Paykel kits (EZKleen stainless steel door panels) and custom door panels are outlined below. For Fisher & Paykel kits, only remove the protective film for handle installation. This will protect the finish of the door panels until installation is complete. French door panels 1 Drawer door panel Mounting handle (refer to A) For Fisher & Paykel door panel sets, remove the plastic plugs from the handle holes x4.
!4 1 HANGING ICE & WATER DOOR PANEL 5 Remove the external display module from inside the product. Thread the display harness through the door panel cavity. Ensure the grommet is engaged. 2 Connect display harness onto the refrigerator door by inserting firmly until you feel it clip securely (refer to B). B On the external display, enable the dispenser lock, this will help prevent any water from dispensing during water connection. To lock, press the button for 4 seconds.
!5 1 ●● ●● ●● HANGING NON-WATER DISPENSING DOOR PANELS 3 Hang all door panels onto M8 studs and align the side bracket forks onto the refrigerator door. Ensure the forks are positioned around the body of the side screws (M5 x 10 pan head Phillips screw). Push the product until the door panels are flush with the front face of the adjacent cabinetry. Place a ruler on the front of the product to check flushness top and bottom, left and right (refer to drawing below).
!6 ICE AND WATER INITIATION Ensure the appliance is switched on and the isolation faucet has been connected and turned on. Water dispenser initiation (Ice & Water models only) Ice maker initiation ●● ●● ●● ●● ●● ●● To initiate ice maker before use: When the appliance is first turned on after installation, the ice maker will be off. To activate the automatic ice maker, press the ‘Ice On/Off’ button once. The LED light above the button will illuminate indicating the ice maker is on.
!7 1 2 Carefully open the refrigerator French doors to attach fixing brackets. Place fixing bracket over the side of the appliance and secure mid-way with screws x2 (M5 x 8 countersunk Phillips screws). 3 Secure the center of each fixing bracket to the side of the adjacent wall with screws x2 (#8 x 19 twin thread screws). 4 Repeat this process for the remaining brackets. 28 ATTACH FIXING BRACKETS Slide screw cover in between the fixing bracket and the side bracket on the appliance x1.
!8 1 ATTACH COVERS AND TOE KICK Note: To complete the integrated appliance, the customer should supply their own toe kick for installation. The hardware required to mount the toe kick is supplied. Remove any remaining protective film on your door panels. A B 2 Open the refrigerator French doors, firmly push top cover over the top studs. 4 Installing toe kick Unscrew the toe kick bracket screws mid-way, and bring forward (refer to A and B). Repeat this process on the opposite side.
MATCHING HOLES ON PLASTIC PARTS !9 ATTACH BOTTOM KICKSTRIP For toe kick installation higher than 4” (102 mm) For toe kick installation at 4” (102 mm) 1 Measure the required height for the bottom grille. On a board, carefully score/cut the un-required vanes from the bottom of the kickstrip grille and discard (refer to A). 2 Drill Ø 5/32” (4 mm) holes into the dimples of the grille (refer to B). Repeat this process for all dimples.
@0 ATTACH SIDE TRIM BRACKETS IMPORTANT! Before installing your appliance, ensure the dimensions of the finished enclosure are correct for your appliance following the ‘Product and cavity dimensions’ sections. Framed cabinetry installation 1 Break off the datum lip to each side trim bracket and discard. Repeat for all side trim brackets. Discard 2” (50 mm) ) Repeat on the opposite side.
@1 ATTACH SIDE TRIMS For 80” (2032 mm) cavity installation only Measure 4” (102 mm) from the top, shorter side trim and carefully cut using a fine tooth hacksaw to a length of 76“ (1930 mm). Refer to A for orientation of side trim. Note: ensure cut is straight and square as this is an exposed surface. Also ensure the plastic part does not bend as this can cause visual stress marks. A Aluminum Plastic Repeat this process for the remaining side trim.
@2 ADJUSTING HINGE TENSIONING SCREWS Hinge tensioning screws can be tightened if increased door closing force is required. 1 To ensure the French doors shut on their own, when pushed within the self close activation range, the hinge tensioning screws need to be tightened. The hinge tensioning screw is located in the French door hinges. To tighten the screw, rotate the screw to the right (refer to A). Repeat this process on the opposite side.
@3 TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the appliance is level. Ensure the appliance is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the doors/drawer can open and close freely with no resistance from surrounding cabinetry. Ensure hinge limiting pin is fitted for 90° door swing. Ensure all internal and external packaging is removed from the appliance before use. Ensure a manual ice maker cycle has been forced.
www.fisherpaykel.com Copyright © Fisher & Paykel 2015. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. US CA 843155 B 08.
