Installation

28
@3 ATTACH BOTTOM TOE KICK
1
Measure the required height for the bottom grille. On a board, carefully score/cut
theexcess vanes from the bottom of the toe kick grille and discard (A).
2
Drill Ø 5/32” (4mm) holes into the dimples of the grille (B).
Repeat this process for all dimples.
2
Align the air flow divider underneath the grille tabs indicator
and clip onto the vanes of the bottom grille (B).
3
With the grille tabs facing upwards, align the grille to the
bottom of the plinth where the screw holes are located
and secure with #8x5/8” pan head screws (3x) (C).
1
With the grille tabs facing upwards, align the grille clips to the bottom
of the plinth’s slots, then firmly push grille onto the plinth (A).
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
B
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
Grille tabs
A
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
D
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
A
Cut excess vanes from the bottom of the grille
B
DETAIL A
SCALE 1 : 1
DETAIL D
SCALE 2 : 1
IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO 1.
CUT UNREQUIRED VANES FROM DOTTOM
DRILL HOLES THROUGH DIMPLES 2.
USE PROVIDED SCREWS TO FIX GRILL TO 3.
MATCHING HOLES ON PLASTIC PARTS
Grille tabs
Front right view
DETAIL B
SCALE 2 : 5
C
For custom toe kick greater than 4” (102mm) For toe kick installation at 4” (102mm)
4
Align the air flow divider underneath the grille tabs indicator
and clip onto the vanes of the bottom grille (D).