FREESTANDING COOKER OR90 Induction models INSTALLATION GUIDE NZ AU
1 SAFETY AND WARNINGS WARNING! Electrical shock hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good ground wiring system is absolutely essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician Failure to follow this advice may result in electrical shock or death. ● ● ● ● ● ● ● WARNING! Cut Hazard Take care – some edges are sharp.
2 PARTS SUPPLIED FOR INSTALLATION Anti-tip bracket and lock pin (1) Screws and plastic sleeve anchors (2) 3 TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE) IMPORTANT! ● ● THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer or the service agent.
4 MODEL IDENTIFICATION NOTE: Model features may vary OR90 INDUCTION MODELS OR90SCI1 OR90SCI4 OR90SCI6 OR90SDI6 5 PRIOR TO INSTALLATION Unpacking and handling ● ● ● Inspect the cooker to verify that there is no shipping damage. If any damage is detected, call the shipper and initiate a damage claim. Fisher & Paykel is not responsible for shipping damage. DO NOT discard any packing material until the cooker has been inspected. Remove the outer carton and any packing material from cooker.
PRODUCT DIMENSIONS NOTE: Model features may vary Optional kickstrip available (purchased separately) C D E A F G FRONT B SIDE OR90SCI MODELS PRODUCT DIMENSIONS A Overall height of cooker (from floor to top of cooktop, excluding optional backguard) mm min 898 max 946 B Overall width of cooker 897 C Overall depth of cooker 600 (from front of cooker to rear of island trim/backguard, excluding handles and dials) C D Height of optional backguard from top of cooktop 60 (supplied with some mo
CLEARANCE DIMENSIONS B C A B COOKING SURFACE F E Electrical (see diagrams following) D ISO FRONT OR90SCI MODELS CLEARANCE DIMENSIONS A Minimum vertical distance between benchtop and cabinet extending above counter B Minimum clearance from left and right edge of cooker to nearest vertical combustible surface mm 450 50 C Minimum clearance from cooking surface to: – Overhead cabinet centered above the cooktop – Ventilation hood centered above the cooktop ● ● 650 650 D Width of cabinetry op
FITTING THE OPTIONAL BACKGUARD 9 LOCATION OF ELECTRICAL SUPPLY Backguard (supplied with some models only) ● ● ● Remove the screws and spacers on the rear of the cooktop. Assemble the backguard as shown and fix onto the back of the cooker using the same screws and spacers. Fix the backguard onto the cooker using the screws provided.
!0 VENTILATION REQUIREMENTS A suitable ventilation hood may be installed above the cooker. Fisher & Paykel has a choice of ventilation hoods designed to match the rest of our kitchen appliance family. See fisherpaykel.com or your local dealer for more details. Hood (inc. combustible) 650mm Wall Installation Hood (inc.
!1 FITTING THE ADJUSTABLE FEET Fitting the adjustable feet Fitting the adjustable feet covers (optional) The adjustable feet must be fitted to the base of the cooker before use. Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet. If using the adjustable feet covers fit these while the cooker is tipped over. IMPORTANT Take care not to damage the cooker during this operation.
!2 MOVING THE COOKER IMPORTANT! ● ● ● When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the adjustable feet. Be careful: do not lift the cooker by the oven door handle, the hob rail or by lifting the cooktop trim as this may damage the appliance. When moving cooker to its final position DO NOT DRAG. Lift feet clear of floor.
!3 INSTALLING THE ANTI-TIP BRACKET IMPORTANT! ● ● ● To restrain the cooker and prevent it tipping accidentally secure the cooker to the wall using the supplied anti-tip bracket. Make sure you also fit the supplied lock pin to the anti-tip bracket. If installing the cooker above a plinth (without fitting the adjustable feet) revise the installation dimensions for the anti-tip bracket accordingly, considering that the feet have the following measurements: min 85mm - max 133mm.
!3 INSTALLING THE ANTI-TIP BRACKET Fitting the lock pin (models with a storage/warming drawer) Fitting the lock pin (models with a storage compartment) The anti-tip bracket is accessible by removing the storage/warmer drawer, and is positioned on the rear right side of the cooker. The anti-tip bracket is accessible by opening the storage compartment door., and is positioned on the rear right side of the cooker. B A 1 Open the storage compartment door.
!4 ELECTRICAL CONNECTION IMPORTANT! ● ● ● ● ● ● ● ● ● ● ● ● This cooker must be connected to the mains power supply only by a suitably qualified person. This cooker must be earthed. If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the electrical system is suitable for the electricity drawn by the cooker.
!5 ELECTRICAL FEEDER CABLE CONNECTION IMPORTANT! The power supply cable must be connected by an authorised service person Feeder cable section Use a type of cable according to the applicable local regulations. 220-240 Vac 3 x 10 mm2* *Connection with wall box connection.
!6 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER F GENERAL Placement of unit. F Specified clearance maintained to cabinet surfaces. F Unit Level – front to back, side to side. F All packaging material and tie straps removed. F Island trim or optional backguard correctly attached. F The anti-tip bracket is correctly installed. F ELECTRICAL Adequate ground connection. F OPERATION All internal packing materials removed. Check inside the oven. F Dials turn correctly and freely.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2017. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. NZ AU 591517A / 1105510-ß0 12.
