FREESTANDING COOKER OR90 Induction models INSTALLATION GUIDE NZ AU
SAFETY AND WARNINGS ! WARNING! WARNING! Electrical Shock Hazard Failure to follow this advice may result in electric shock or death. Tipping Hazard Failure to do so can result in death or serious burns to children of adults. • Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. • To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip device packed with the appliance.
SAFETY AND WARNINGS WARNING! To avoid hazard, follow these instructions carefully before installing or using this appliance. GENERAL INSTALLATION INFORMATION Cleaning and servicing z z z z z z z z z z z z z z z z Please make this information available to the person installing the appliance — doing so could reduce your installation costs.
PARTS SUPPLIED FOR INSTALLATION Anti-tip bracket and lock pin (1) Screws and plastic sleeve anchors (2) TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE) IMPORTANT! THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer or the service agent. z The use of suitable protective clothing/gloves is recommended when handling or installing this appliance.
MODEL IDENTIFICATION Model features may vary. OR90 Induction models OR90SCI1 OR90SCI4 OR90SCI6 OR90SDI6 PRIOR TO INSTALLATION Unpacking and handling z z z Inspect the cooker to verify that there is no shipping damage. If any damage is detected, call the shipper and initiate a damage claim. Fisher & Paykel is not responsible for shipping damage. DO NOT discard any packing material until the cooker has been inspected. Remove the outer carton and any packing material from cooker.
PRODUCT DIMENSIONS Model features may vary. Optional kickstrip available (purchased separately). C D e a F G FRONT PROFILE B OR90SCI PRODUCT DIMENSIONS mm 1 Overall height of cooker (from floor to top of cooktop, excl. optional backguard) C 2 Overall width of cooker 897 3 Overall depth of cooker (from front of cooker to rear of island trim/backguard, excl. handles and dials) 600 4 Height of optional backguard from top of cooktop (supplied with some models only) 60 5 Height of chassis (excl.
CLEARANCE DIMENSIONS C A B Cooking surface B F E Electrical & Gas (see diagrams following) D FRONT ISO OR90SCI CLEARANCE DIMENSIONS Note: z mm A Minimum vertical distance between benchtop and cabinet extending above counter B Minimum clearance from left and right edge of cooker to nearest vertical combustible surface 450 z 50 z C Minimum clearance from cooking surface to: z Overhead cabinet centered above the cooktop z Ventilation hood centered above the cooktop 650 650 D Width of cabinetry
FITTING THE OPTIONAL BACKGUARD LOCATION OF ELECTRICAL SUPPLY Backguard (supplied with some models only) z z z Remove the screws and spacers on the rear of the cooktop. Assemble the backguard as shown and fix onto the back of the cooker using the same screws and spacers. Fix the backguard onto the cooker using the screws provided.
VENTILATION REQUIREMENTS A suitable ventilation hood may be installed above the cooker. Fisher & Paykel has a choice of ventilation hoods designed to match the rest of our kitchen appliance family. See fisherpaykel.com or your local dealer for more details. IMPORTANT z z Consult local building codes and/or local agencies, before starting, to ensure that hood and duct installation will meet local requirements.
FITTING THE ADJUSTABLE FEET Fitting the adjustable feet Fitting the adjustable feet covers (optional) The adjustable feet must be fitted to the base of the cooker before use. If using the adjustable feet covers fit these while the cooker is tipped over. Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet. IMPORTANT Take care not to damage the cooker during this operation. 1 Tip cooker onto its back and fix brackets to mounting holes.
MOVING THE COOKER IMPORTANT! z z z z When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the adjustable feet. BE CAREFUL: do not lift the cooker by the oven door handle, the hob rail or by lifting the cooktop trim as this may damage the appliance. When moving cooker to its final position DO NOT DRAG. Lift feet clear of floor.
INSTALLING THE ANTI-TIP BRACKET IMPORTANT! z z z To restrain the cooker and prevent it tipping accidentally secure the cooker to the wall using the supplied anti-tip bracket. Ensure you also fit the supplied lock pin to the anti-tip bracket. If installing the cooker above a plinth (without fitting the adjustable feet) revise the installation dimensions for the anti-tip bracket accordingly, considering that the feet have the following measurements: min 85mm – max 133mm.
INSTALLING THE ANTI-TIP BRACKET Fitting the lock pin (models with a storage/warming drawer) Fitting the lock pin (models with a storage compartment) The anti-tip bracket is accessible by removing the storage/warmer drawer, and is positioned on the rear right side of the cooker. The anti-tip bracket is accessible by opening the storage compartment door, and is positioned on the rear right side of the cooker. B A To remove the storage/warming drawer 1 Open the storage compartment door.
ELECTRICAL CONNECTION IMPORTANT! z This cooker must be connected to the mains power supply only by a suitably qualified person. This cooker must be earthed. z If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the electrical system is suitable for the electricity drawn by the cooker.
ELECTRICAL FEEDER CABLE CONNECTION IMPORTANT! The power supply cable must be connected by a Fisher & Paykel trained and support service technician or qualified person. Feeder cable section Use a type of cable according to the applicable local regulations. 220-240 V AC L 1 Remove the screws that hold the cover in place at the back of the cooker. N PE 2 Unscrew the bottom terminal end of the strain relief by using two spanners.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL OPERATION F Placement of unit. F All internal packing materials removed. Check inside the oven. F Specified clearance maintained to cabinet surfaces. F Dials turn correctly and freely. F Unit Level — front to back, side to side. F Oven and cooktop displays are functioning correctly and oven and cooking zones can be turned on. F All packaging material and tie straps removed. F Oven door hinges seated and door opens and closes properly.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this document correctly describes the product currently available. NZ AU 591517B 06.
