CLASSIC RANGEHOOD HC90PCTX1, HC90PCB1, HC90PCW1 and HC90PCR1 models INSTALLATION GUIDE NZ AU
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. • This appliance is equipped with a three-prong or four-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded power outlet. • Never remove the grounding plug or use with a 2 prong adapter. • Do not immerse cord or plugs in water or other liquid.
PARTS SUPPLIED PRIOR TO INSTALLATION Fisher & Paykel is not liable for any damage caused by not following these instructions. z z z z z z Rangehood hood (1) Installation guide (1) Chimney (1) z z z Upper chimney bracket (1) Chimney bracket (1) Expansion plug (10) Upper chimney (1) 150 mm diameter ducting adapter with damper (1) 10 mm self-tapping screw (4) Please read the instructions carefully. Unpack the rangehood.
PRODUCT DIMENSIONS i j Power cord location h d PLAN g f A b MM A Maximum overall height of product 975 B Minimum overall height of product 636 C Overall width of product 898 D Overall depth of product 500 E Height of hood 298 F Width of chimney 320 G Depth of chimney 290 H Distance from centre of ducting outlet to back of product e c PROFILE PRODUCT DIMENSIONS I Distance from centre of ducting outlet to side of chimney 160 J Diameter of ducting outlet 150 K Distance between c
INSTALLATION HEIGHT ATTACHMENT DIMENSIONS H A G Upper chimney bracket attachment points E Chimney bracket attachment points B C F Upper rangehood hood attachment points D Lower rangehood attachment points B A HEIGHT DIMENSIONS MM A Ducted installation z Minimum height z Maximum height 636 Recirculation z Minimum height z Maximum height 676 B Height from top of cooktop to base of product 975 975 650 – 750 This rangehood must be installed no lower than the minimum height indicated in the
VENTING OPTIONS Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled. The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to operate with the exhaust air recirculating within the kitchen. Ducted Recirculating For ducted installation it is recommended that 150 mm diameter, rigid or semi-rigid ducting is used. This will require a 160 mm (min) round hole in the ceiling or wall.
ELECTRICIAL REQUIREMENTS PREPARE RANGEHOOD Warning: Failure to install the screws or fixing device in accordance with these instructions may result in an electrical hazards. 1 Place the ducting adapter onto the rangehood and screw it into place using 10mm screws. 2 Remove the filters – pull the catch and tilt the filter downwards until it disengages from the supports.
ATTACH BRACKETS AND MOUNTING SCREWS 1 Temporarily mark the height of the bottom of the rangehood and the centre of the cooktop on the wall according to the information provided in 'Installation Height'. 2 Attach the chimney bracket and upper chimney bracket (if using the upper chimney). Use the 30mm screws and expansion plugs if attaching to masonry. Attach the upper hood mounting screws. Use the 30mm screws and expansion plugs if attaching to masonry.
ATTACH CHIMNEY 1 Bend the tabs on the chimney. Rear view 2 Place chimney around the rangehood chassis and hang off the chimney bracket. 3 Extend the upper chimney and attach to the upper chimney bracket with 10mm screws.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Rangehood is correctly installed All connections are secure Connections have not pierced any electrical or water lines within the wall Ducting has not been crushed or bent in any area's Flexible ducting has been pulled taut and any excess removed (if required) Power plug switch is accessible to the customer Product is plugged in and power switched on Operation of the product has been tested Complete and keep for safe reference: Model Serial no.
FISHERPAYKEL.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this document correctly describes the product currently available. NZ AU 105939A 12.
