Installations Instructions

5
6 METTEZ L’EMBALLAGE AU REBUT
8 APPLIQUEZ L’ISOLANT ADHÉSIF AUTOUR DUREBORD
7 INSTALLEZ LE COUDE ET LA RONDELLE
9 DÉPOSEZ L’APPAREIL DOUCEMENT DANS L’OUVERTURE
Nipple (½” NPT thread)
Foam Tape
Adhesive side
Ensure edge of tape
lines up with outer
edge of cooktop
Recyclez de façon responsable
Le modèle peut être différent des
illustrations présentées
Coude (avec filetage NPT externe
de 1/2po (12,5mm))
GAS
ON
GAS
ON
PTFE
⁄” NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG LPG
LPG
20-50 mm
½ “ BSP
½ “ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
min
S
A
R
min
A
F
S
REAR CLAMPS FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm 30 mm
Foam Tape
Adhesive side
Ensure edge of tape
lines up with outer
edge of cooktop
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut o by the customer, make sure the connection
is tted with an isolating valve close to the cooktop.
Make sure to t the supplied
washer and regulator.
Adjust to obtain a test point
pressure of 1 kPa with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certied, with an Rp ½” (ISO 71) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, ue, or chassis of underbench oven etc.)
If connecting the gas with a exible hose:
LPG Models
check all connections
Make sure to t the supplied
washer and test point adaptor.
Make sure the supply pressure
is regulated to 2.75 kPa, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tiplifting o
good ame
Arrow
x 4
x 4
30-40mm
40mm+
GAS
ON
GAS
ON
PTFE
⁄” NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG LPG
LPG
20-50 mm
½ “ BSP
½ “ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
min
S
A
R
min
A
F
S
REAR CLAMPS FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm 30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut o by the customer, make sure the connection
is tted with an isolating valve close to the cooktop.
Make sure to t the supplied
washer and regulator.
Adjust to obtain a test point
pressure of 1 kPa with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certied, with an Rp ½” (ISO 71) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, ue, or chassis of underbench oven etc.)
If connecting the gas with a exible hose:
LPG Models
check all connections
Make sure to t the supplied
washer and test point adaptor.
Make sure the supply pressure
is regulated to 2.75 kPa, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tiplifting o
good ame
Arrow
x 4
x 4
30-40mm
40mm+
Rondelle en fibre
1 Retournez la surface de cuisson à
l’envers sur unesurface douce.
2 Appliquez le joint autour des rebords
en plaçant le côté adhésif vers le bas,
pour obtenir un joint continu autour de
la surface de cuisson.
3 Utilisez un outil de coupe tranchant
ou des ciseaux pour couper l’excédent
de matériel de scellement autour du
rebord de la surface de cuisson. Veillez
à ne pas endommager le comptoir.
GAS
ON
GAS
ON
PTFE
⁄” NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG LPG
LPG
20-50 mm
½ “ BSP
½ “ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
min
S
A
R
min
A
F
S
REAR CLAMPS FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm 30 mm
Isolant adhésif
Côté adhésif
Assurez-vous que
le rebord de l’isolant s’aligne
avec le rebord extérieur de
la surface de cuisson
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut o by the customer, make sure the connection
is tted with an isolating valve close to the cooktop.
Make sure to t the supplied
washer and regulator.
Adjust to obtain a test point
pressure of 1 kPa with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certied, with an Rp ½” (ISO 71) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, ue, or chassis of underbench oven etc.)
If connecting the gas with a exible hose:
LPG Models
check all connections
Make sure to t the supplied
washer and test point adaptor.
Make sure the supply pressure
is regulated to 2.75 kPa, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tiplifting o
good ame
Arrow
x 4
x 4
30-40mm
40mm+
Écrou flottant