™ T8.
TABLE OF CONTENTS Warnings.....................................................................................................................................................................................................3 Quick Start Guide.......................................................................................................................................................................................4 T8.1 Diagram........................................................................
QUICK START GUIDE T8.1 DIAGRAM Thank you for purchasing the First Strike 8.1 Pistol. Like any paintball marker, it is important that safety is on the forefront of your mind at all times when using this product. Never operate the 8.1 without ASTM compliant goggles or aim at anyone that is not wearing proper goggles intended for the game of Paintball. The First Strike T8.
T8.1 MAGAZINE DIAGRAM OPERATIONAL INSTRUCTIONS GETTING STARTED PROJECTILE RETAINER PIN Read this entire manual before using this launcher. Keep your launcher pointed in a safe direction at all times. 1. SAFETY - Place the T8.1 in safe position by moving safety so no red is visible. The safety is ambidextrous and can be operated from either side of the T8.1. * Visible red indicates that launcher will discharge. PROJECTILE FOLLOWER TRACK 2.
OPERATIONAL INSTRUCTIONS 4. LOAD PROJECTILES - Place 8 projectiles into the magazine from the top. The projectiles will be held in place automatically by the projectile retainer pin. You can also lock the ball pusher in the down position by pulling down on the ball pusher ears and locking them at the bottom of the ball pusher track. OPERATIONAL INSTRUCTIONS LOAD PROJECTILE RED SPRING/SILVER SPRING When using First Strike™ projectiles, make sure the red magazine spring is installed.
OPERATIONAL INSTRUCTIONS OPERATIONAL INSTRUCTIONS FIRING THE T8.1 1. If the CO2 cartridge has been punctured by the puncture pin and the magazine has been inserted into the gun, then the T8.1 is now ready to fire. Point the T8.1 in a safe direction, rotate the safety so red is visible, and pull the trigger. NOTE: Extra magazines can be carried for quick reloads in the field. UNLOADING THE T8.1 1. Place T8.1 in the safe mode and point in a safe direction.
T8.1 CLEANING & MAINTENANCE CLEANING • Never perform maintenance on a loaded or pressurized T8.1 marker. • Remove all projectiles and CO2 cartridges from the magazine and marker prior to doing any cleaning or maintenance. • Never use petroleum based cleaning solvents or lubricants. • Do not use cleaning solvents that come in aerosol cans. • To clean the T8.1 marker, remove the barrel as described in the “Operational Instructions”. Use a .
T8.1 ASSEMBLY DIAGRAM ITEM NO. 1 2 3 4 5 6 7 8 NAME ITEM NO. Gun Body Assembly Handle Trigger Pin Handle Screw-Front Firing Bolt Spring T8.1 FS Barrel Magazine Assembly Safety Bushing GUN BODY ASSEMBLY NAME ITEM NO. 9 10 11 Safety-Left Safety-Right Safety Spring 12 Safety Pin 13 Front Handle Screw Washer 14 Remote Plug Set Screw 15 Rubber Nubbin 1 2 3 4 5 6 7 8 NAME ITEM NO. Engine Assembly 8.
ENGINE & FIRING BOLT ASSEMBLY ITEM NO. 1 2 3 4 5 6 7 TRIGGER GROUP NAME ITEM NO. Air Chamber Plug Air Chamber AC Shock Absorber AC Cap O-Ring First Strike Firing Bolt AC Plug O-Ring AC OD O-Ring 1 6 2 7 3 14 5 6 4 bolt and firing pin (Item NOTE: Do not attempt to disassemble 5). The alignment is set by factory fixtures and cannot be reassembled outside the3 factory.
REGULATOR ITEM NO. MAGAZINE NAME 1 2 3 4 5 6 7 8 ITEM NO. Regulator Body Regulator Adjuster Stem Regulator Sealing Screw Reg Sealing/Reg Body O-Ring Reg Body Plug Regulator Spring Pad O-Ring C02 Stem O-Ring NAME ITEM NO. 9 10 11 Regulator Spring Regulator End Screw Regulator Valve Sleeve 12 Regulator Valve O-Ring 13 Regulator End Screw O-Ring 14 Regulator Valve Spring 15 Regulator Valve Ball 16 Regulator Spring Pad 15 1 2 7 9 1 16 2 9 10 16 7 14 ITEM NO.
CO2 VALVE HOUSING ITEM NO. 1 2 3 4 5 6 7 8 9 TROUBLESHOOTING PAINT BREAKAGE NAME C02 Valve Body C02 Puncture Tip C02 Valve Spring Housing O-Ring C02 Valve Spacer O-Ring C02 Valve Cap C02 Seal C02 Drum Valve Valve Spacer If you experience more than a small number of broken paintballs, check the following: 6 1. First, be sure that the marker is free of broken paintballs and other debris. 2.
NOTES T8.1 WARRANTY REGISTRATION CARD: NAME: ADDRESS: DATE OF PURCHASE: SERIAL NUMBER: Please detach from product manual, place in stamped envelope and send to: First Strike Paintball Warranty Support 2717 Ferguson Rd. Fort Wayne, IN 46809 " 22 | T8.
FIRST STRIKE® Headquarters: 28101 Ballard Dr. Ste. F Lake Forest, IL 60045 Manufacturing/Warranty 2717 Ferguson Rd Fort Wayne, IN 46809 1-260-478-2500 service@first-strike.com FIRST-STRIKE.COM © 2017 United Tactical Systems. All rights reserved. This United Tactical Systems product is protected by United States and International Patents. United Tactical Systems Trademarks, Designs and Copyrights are protected by United States and International Law.
