Use and Care Manual

-5-
7. Tap the Adjust UP/DOWN button repeatedly to set the date. Press and hold the buttons to speed up the
forward or reverse scanning of the digits.
8. Tap the MODE button to finish the setting. Tap the MODE button 3 times or wait for few seconds to exit
calendar setting mode.
ALARM SETTING
Setting the Alarm Time
1. In clock display mode, tap the MODE button twice to enter the Alarm setting mode, the alarm indicator
and time 12:00 appear on the display.
2. Press and hold the MODE button for 3 seconds, the Hour digits will flash.
3. Tap the Adjust UP/DOWN button repeatedly to set the hour value. Press and hold the buttons to speed up
the forward or reverse scanning of the digits.
Note: Make sure the hour is set so that the PM indicator is displayed correctly.
4. Tap the MODE button after the hour is set, the Minute digits flash to prompt for input.
5. Tap the Adjust UP/DOWN button repeatedly to set the minute value. Press and hold the button to speed
up the forward or reverse scanning of the digits.
6. Tap the MODE button after minute is set, Alarm melody type “00” flashing to prompt for input. There are
total 13 kinds of alarm melody (00-12) available for selection.
7. Tap the Adjust UP/DOWN button repeatedly to select the alarm melody you desired.
8. Tap the MODE button to finish the setting. Tap the MODE button twice again or wait for few seconds to
exit alarm setting mode.
9. Alarm will sound for 2 minutes when set time comes. Tap the MODE button once to turn off the alarm until
next day.
Note: The Display will blink when the alarm is sounding.
Turning the Alarm ON/OFF
In clock display mode,
- Tap the ALARM ON/OFF button repeatedly in alarm OFF mode until the alarm icon appears on display
to turn on the alarm.
- Tap the ALARM ON/OFF button repeatedly in alarm ON mode until the alarm icon disappear from
display to turn off the alarm.
SNOOZE
- When the alarm sounds, it can be temporarily stopped by pressing the SNOOZE/LIGHT button on top
Z
panel or SNOOZE button on back. Snooze indicator Z appears in display and flashing with Alarm
indicator together.
- The alarm will be delayed for 8 minutes and then come again.
- This manual snooze operation can be repeated again and again while alarm sounding.
SPECIAL DAY REMINDER SETTING
1. In clock display mode, tap the MODE button three times to enter the special day reminder setting mode.
The Month and Date of reminder indicator will appear in display.
Note: Make sure you are in special day setting mode, and not in calendar mode.
2. Press and hold the MODE button for 3 seconds, the reminder month digit flashes. Tap the Adjust UP/
DOWN button repeatedly to set your reminder month.
3. Tap the MODE button to confirm, the date digit flash. Tap the Adjust UP/ DOWN button repeatedly to set
your reminder date.
4. Tap the MODE button to confirm, the hour digits flash. Tap the Adjust UP/ DOWN button repeatedly to set
the hour.
Note: Make sure the hour is set so that the PM indicator is displayed correctly.
5. Tap the MODE button to confirm, the minute digits flash. Tap the Adjust UP/ DOWN button repeatedly to
set the minute.
6. Tap the MODE button to finish the setting. Special Day reminder indicator will show on the display.
7. The Special Day melody will play for 2 minutes when set date comes if not interrupted, the reminder
indicator will be flashing on the display.
8. Press any button to stop the melody immediately. It will sound again next year on the same day set.
Note: The Snooze has no effect on the special day reminder.
9. To cancel the special day reminder, tap the ALARM ON/OFF repeatedly until the special day reminder
indicator goes off on the display.
INDOOR TEMPERATURE OPERATION
INDOOR WEATHER MEASUREMENT
NOTE: 1.) The main unit display backlight will remain lit when using the AC power adaptor.
2.) When using battery power, the backlight will turn off automatically to save battery power. Press
the LIGHT/SNOOZE button once, and the backlight will turn on for 7 seconds.