User Guide

–
7
–
CONFIGURABLE ZONE TYPE OPTIONS (*182-*185)
✱
182
CONFIGURABLE ZONE TYPE 90
12345678910
Enter the appropriate value for each entry, 1-10, based on the charts provided on
next page. Each entry is the sum of the values of its selected options
(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).
UL: Do not configure zones as a fire alarm or UL burglar alarm zone.
✱
183
ZONE TYPE 90 REPORT CODES
IMPORTANT:
Use existing Contact ID®
codes, if appropriate, or define unique codes
in CID code range 750-789. See important
note in installation instructions.
90 ALARM ID: XXX
TROUBLE ID: XXX
Enter the desired 3-digit Contact ID® report codes for
alarms and troubles occurring on zones assigned to
this zone type. Enter the codes sequentially (all 6
digits). When entering digits, [#] moves cursor back, [
∗
]
moves forward. Press [
∗
] when done to continue.
✱
184
CONFIGURABLE ZONE TYPE 91
12345678910
Enter the appropriate value for each entry, 1-10, based on the charts provided on
next page. Each entry is the sum of the values of its selected options
(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).
UL: Do not configure zones as a fire alarm or UL burglar alarm zone.
✱
185
ZONE TYPE 91 REPORT CODES
IMPORTANT:
Use existing Contact ID®
codes, if appropriate, or define unique codes
in CID code range 750-789. See important
note in installation instructions.
91 ALARM ID: XXX
TROUBLE ID: XXX
Enter the desired 3-digit Contact ID® report codes for
alarms and troubles occurring on zones assigned to
this zone type. Enter the codes sequentially (all 6
digits). When entering digits, [#] moves cursor back, [
∗
]
moves forward. Press [
∗
] when done to continue.
KEYPAD OPTIONS (*190-*196
NOTE
: Options for keypad address 16 are set by the factory and cannot be changed.)
NOTE:
Each keypad must be assigned a unique address. Keypads programmed with the same address will give
unpredictable results.
✱
190
KEYPAD 2 ADDRESS 17
[0] [0]
Partition/ Sound
Enable
FA168C: enter partition
FA148CP: 1 = enable
0 = disable
Partition: 0 = keypad disabled; 1-3 = part. no. (3 = com)
Sound: 0 = no suppression
1 = suppress arm/disarm and E/E beeps
2 = Suppress chime beeps only
3 = suppress arm/disarm, E/E, and chime
beeps
✱
191
KEYPAD 3 ADDRESS 18
[0] [0]
Part./Enable
†
Sound
See field
∗
190 for entries.
† FA168C: enter partition
FA148CP: 1 = enable; 0 = disable
✱
192
KEYPAD 4 ADDRESS 19
[0] [0]
Part. /Enable
†
Sound
See field
∗
190 for entries.
† FA168C: enter partition
FA148CP: 1 = enable; 0 = disable
✱
193
KEYPAD 5 ADDRESS 20
[0] [0]
Part. /Enable
†
Sound
See field
∗
190 for entries.
† FA168C: enter partition
FA148CP: 1 = enable; 0 = disable
✱
194
KEYPAD 6 ADDRESS 21
[0] [0]
Part. /Enable
†
Sound
See field
∗
190 for entries.
† FA168C: enter partition
FA148CP: 1 = enable; 0 = disable
✱
195
KEYPAD 7 ADDRESS 22
[0] [0]
Part. /Enable
†
Sound
See field
∗
190 for entries.
† FA168C: enter partition
FA148CP: 1 = enable; 0 = disable
✱
196
KEYPAD 8 ADDRESS 23
[0] [0]
Part. /Enable
†
Sound
See field
∗
190 for entries.
† FA168C: enter partition
FA148CP: 1 = enable; 0 = disable
✱
197
EXIT TIME DISPLAY INTERVAL
[0]
0 = no display; 1-5 = seconds between display refresh
✱
198
DISPLAY PARTITION NUMBER
(for Alpha Display Keypads)
[0]
0 = no; 1 = yes (partition no. appears on Alpha Display)
✱
199
ECP FAIL DISPLAY
[0]
0 = 3-digit display (“1” + device address)
1 = 2-digit fixed-display as “91”