How to Guide

ManualsBrandsFirst Alert ManualsElectrical10-Year 2-Pack Battery-Operated 120-Volt Photoelectric Sensor Smoke Detector

INTRODUCTION (CONTINUED)...

Red Blinking Power Indicator every 6 minutes: Confirms that the smoke alarm is receiving power.

All First Alert

smoke alarms conform to regulatory requirements, including UL217 and are designed to

detect particles of combustion. Smoke particles of varying number and size are produced in all fires.

Ionization technology is generally more sensitive than photoelectric technology at detecting small particles, which

tend to be produced in greater amounts by flaming fires, which consume combustible materials rapidly and spread

quickly. Sources of these fires may include paper burning in a wastebasket, or a grease fire in the kitchen.

Photoelectric technology is generally more sensitive than ionization technology at detecting large particles,

which tend to be produced in greater amounts by smoldering fires, which may smolder for hours before

bursting into flame. Sources of these fires may include cigarettes burning in couches or bedding.

For maximum protection, use both types of smoke alarms on each level and in every bedroom of your home.

BASIC SAFETY INFORMATION

•

This unit will not alert hearing impaired residents. It is recommended that you install special

units which use devices like flashing strobe lights to alert hearing impaired residents.

•

Do not connect this unit to any other alarm or auxiliary device. It is a single-station unit that cannot be

linked to other devices. Connecting anything else to this unit may prevent it from working properly.

•

Unit will not operate without battery power. The smoke alarm cannot

work until you activate the battery power pack.

•

Do not install this unit over an electrical junction box. Air currents around junction

boxes can prevent smoke from reaching the sensing chamber and prevent the unit from

alarming. Only AC powered units are intended for installation over junction boxes.

•

Do not stand too close to the unit when the alarm is sounding. It is loud to wake you in

an emergency. Exposure to the horn at close range may harm your hearing.

•

Do not paint over the unit. Paint may clog the openings to the sensing

chamber and prevent the unit from operating properly.

BEFORE YOU INSTALL THIS SMOKE ALARM

Important! Read “Recommended Locations for Smoke Alarms” and “Locations to Avoid for Smoke Alarms”

before beginning. This unit monitors the air, and when smoke reaches its sensing chamber, it alarms. It can

give you more time to escape before fire spreads. This unit can ONLY give an early warning of developing fires

if it is installed, maintained and located where smoke can reach it, and where all residents can hear it, as

described in this manual. This unit will not sense gas, heat, or flame. It cannot prevent or extinguish fires.

Understand The Different Type of Smoke Alarms: Battery powered or electrical? Different smoke

alarms provide different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms: Fire Safety Professionals recommend at least one smoke alarm

on every level of your home, in every bedroom, and in every bedroom hallway or separate sleeping area. See

“Recommended Locations for Smoke Alarms” and “Locations to Avoid for Smoke Alarms” for details.

Know What Smoke Alarms Can and Can’t Do: A smoke alarm can help alert you to fire, giving you precious time to

escape. It can only sound an alarm once smoke reaches the sensor. See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes: This smoke alarm is designed to be used in a typical single-

family home. It alone will not meet requirements for boarding houses, apartment buildings,

hotels or motels. See “Special Compliance Considerations” for details.

LOCATIONS TO AVOID FOR SMOKE ALARMS

FOR BEST PERFORMANCE, IT IS RECOMMENDED YOU AVOID INSTALLING SMOKE ALARMS IN THESE AREAS:

•

Where combustion particles are produced. Combustion particles form when something burns. Areas to avoid include

poorly ventilated kitchens, garages, and furnace rooms. Keep units at least 20 feet (6 meters) from the sources of

combustion particles (stove, furnace, water heater, space heater) if possible. In areas where a 20-foot (6-meter)

distance is not possible – in modular, mobile, or smaller homes, for example – it is recommended the smoke alarm be

placed as far from these fuel-burning sources as possible. The placement recommendations are intended to keep these

alarms at a reasonable distance from a fuel-burning source, and thus reduce “unwanted” alarms. Unwanted alarms can

occur if a smoke alarm is placed directly next to a fuel-burning source. Ventilate these areas as much as possible.

•

In air streams near kitchens. Air currents can draw cooking smoke into the

sensing chamber of a smoke alarm near the kitchen.

•

In very damp, humid or steamy areas, or directly near bathrooms with showers. Keep units

at least 10 feet (3 meters) away from showers, saunas, dishwashers, etc.

•

Where the temperatures are regularly below 40˚ F (4.4˚ C) or above 100˚ F (37.8˚ C), including

unheated buildings, outdoor rooms, porches, or unfinished attics or basements.

•

In very dusty, dirty, or greasy areas. Do not install a smoke alarm directly over the

stove or range. Keep laundry room smoke alarms free of dust or lint.

•

Near fresh air vents, ceiling fans, or in very drafty areas. Drafts can blow smoke

away from the unit, preventing it from reaching the sensing chamber.

•

In insect infested areas. Insects can clog openings to the sensing chamber and cause unwanted alarms.

•

Less than 12 inches (305mm) away from fluorescent lights. Electrical “noise” can interfere with the sensor.

•

In “dead air” spaces. “Dead air” spaces may prevent smoke from reaching the smoke alarm.

LOCATIONS TO AVOID FOR SMOKE ALARMS (CONTINUED)...

AVOIDING DEAD AIR SPACES

“Dead air” spaces may prevent smoke from reaching the smoke alarm. To avoid

dead air spaces, follow the installation recommendations below.

On ceilings, install smoke alarms as close to the center of the ceiling as possible. If this is not

possible, install the smoke alarm at least 4 inches (102 mm) from the wall or corner.

For wall mounting (if allowed by building codes), the top edge of smoke alarms should be placed between

4 and 12 inches (102 and 305 mm) from the wall/ceiling line, below typical “dead air” spaces.

On a peaked, gabled, or cathedral ceiling, install the first smoke alarm within 3 feet (0.9 meters) of the peak

of the ceiling, measured horizontally. Additional smoke alarms may be required depending on the length, angle,

etc. of the ceiling’s slope. Refer to NFPA 72 for details on requirements for sloped or peaked ceilings.

HOW TO INSTALL THIS SMOKE ALARM

This unit is designed to be mounted on the ceiling, or on the wall if necessary.

Tools you will need: pencil, drill with 3/16" (5 mm) drill bit, standard flathead screwdriver, hammer

THE PARTS OF THIS

SMOKE ALARM

1. Test/Silence button

2. Dual power indicator light and

alarm indicator: Green LED

provides visual indication of an

alarm memory condition; Red

LED provides visual indication

of an alarm and hush modes

1. Mounting bracket

2. Mounting slots

3. Turn this way to attach

4. Turn this way to remove

TO UNLOCK THE

MOUNTING BRACKET

1. Insert a flathead screwdriver

in between the mounting

bracket and the locking pin.

2. Pry the alarm away from

the bracket by pushing up

the screwdriver and turning

the alarm counterclockwise

(left) at the same time.

TESTING & MAINTENANCE

WEEKLY TESTING

•

NEVER use an open flame of any kind to test this unit. You might

accidentally damage or set fire to the unit or to your home.

•

If the alarm ever fails to test properly, replace it immediately. Products under warranty may

be returned to the manufacturer for replacement. See “Limited Warranty” for details.

•

DO NOT stand close to the alarm when the horn is sounding. Exposure at close range may

be harmful to your hearing. When testing, step away when horn starts sounding.

It is important to test this unit every week to make sure it is working properly. Using the Test/Silence button is the

recommended way to test this smoke alarm. Press and hold the Test/Silence button on the cover of the unit until

the alarm sounds (the unit may continue to alarm for a few seconds after you release the button). If it does not

alarm, make sure the unit is receiving power and test it again. If it still does not alarm, replace it immediately. During

testing you will hear a loud, repeating horn pattern: 3 beeps, pause, 3 beeps, pause. Red LED flashes rapidly.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but there are

a few simple things you must do to keep it working properly.

•

Test it at least once a week.

•

Clean the smoke alarm at least once a month; gently vacuum off any dust using your household vacuum’s soft brush

attachment, and test the smoke alarm after cleaning. Never use water, cleaners or solvents since they may damage the unit.

•

If the smoke alarm becomes contaminated by excessive dirt, dust and/or grime, and

cannot be cleaned to avoid unwanted alarms, replace the unit immediately.

•

Relocate the unit if it sounds frequent unwanted alarms. See “Locations to Avoid for Smoke Alarms” for details.

•

When the battery becomes weak, the smoke alarm unit will “chirp” approximately once a

minute (the Low Battery Warning). This Low Battery Warning should last for up to 30 days,

but you should replace the smoke alarm immediately to continue your protection.

Actual service life depends on the smoke alarm and the environment in which it is installed. You MUST

replace the smoke alarm immediately once the unit starts “chirping” (the “Low Battery Warning”).

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking materials properly. Never smoke in bed. 2)

Keep matches or lighters away from children; 3) Store flammable materials in proper containers; 4) Keep electrical

appliances in good condition and don’t overload electrical circuits; 5) Keep stoves, barbecue grills, fireplaces and

chimneys grease- and debris-free; 6) Never leave anything cooking on the stove unattended; 7) Keep portable heaters

and open flames, like candles, away from flammable materials; 8) Don’t let rubbish accumulate. Keep alarms clean,

and test them weekly. Replace alarms immediately if they are not working properly. Smoke alarms that do not work

cannot alert you to a fire. Keep at least one working fire extinguisher on every level, and an additional one in the

kitchen. Have fire escape ladders or other reliable means of escape from an upper level in case stairs are blocked.

OPTIONAL LOCKING FEATURE

The optional locking feature is designed to prevent

unauthorized removal of the alarm. It is not necessary

to activate the lock in single-family households where

unauthorized alarm removal is not a concern.

Tools you will need: Needle-nose pliers or

utility knife, standard flathead screwdriver

Loc

king Pin

The feature uses a locking pin which is molded into the mounting bracket.

Remove locking pin by using needle-nose pliers or a utility knife.

To permanently remove the locking pin, insert a flathead screwdriver between

the locking pin and the lock and pry the pin out of the lock.

TO LOCK THE

MOUNTING BRACKET

1. Using needle-nose pliers,

detach the pin from the

mounting bracket.

2. Insert the locking pin

through the hole on the

back of the smoke alarm

as shown in the diagram.

3. When you attach the alarm

to the mounting bracket the

locking pin’s head will fit

into a notch on the bracket.

FOLLOW THESE SIMPLE STEPS

1. Hold the mounting bracket against the ceiling (or wall) so

the two clusters of universal mounting holes are aligned

approximately at the 9:00 and 3:00 o’clock positions. See

image. Choose one of the three sets of holes shown, A, B

or C (see image) and trace around one of the sets. Be sure

to choose a top and bottom slot on opposite sides so you

can rotate the universal mounting bracket into position

later. This will make it easier in the future to remove the

mounting bracket without completely removing the screws.

WARNING! Do not install this alarm over an

existing electrical box. Only AC powered units are

intended for installation over electrical boxes.

2. Put the unit where it won’t get covered with

dust when you drill the mounting holes.

3. Using a 3/16" (5 mm) drill bit, drill a hole through

the center of the oval outlines you traced.

4. Insert the plastic screw anchors (in the plastic bag with screws)

into the holes. Tap the screw anchors gently with a hammer,

if necessary, until they are flush with the ceiling or wall.

5. Install the screws but do not tighten completely. Attach

the mounting bracket by aligning the screws in the open

portion of the universal mounting slots and rotating the

bracket into place. Tighten the screws until they are

snug to secure the bracket. Do not over tighten.

Mounting Hole Sets

6. Activating the battery. Mount alarm to mounting bracket to activate. Once unit is activated,

it cannot be turned off. Make sure the alarm is locked into the mounting bracket.

NOTE: After you activate the battery, the power indicator light may flash. (If the unit alarms, the

light will blink rapidly, and the horn will repeatedly sound 3 beeps, pause, 3 beeps.) Once the

smoke alarm is on the bracket, you can rotate the alarm to adjust the alignment.

7. Test the alarm. See “Weekly Testing.”

TO PERMANENTLY DEACTIVATE THE SMOKE ALARM

8. After 10 years of operation or Low Battery Warning, deactivate

the alarm: Insert a tool below edge where shown and break

tab. Then slide activation switch to deactivate mode.

NOTE: At end of life or low battery indication (chirp): unit

must be put into deactivation mode to deactivate remaining

stored energy in battery. Unit will no longer function

once put into this mode. Unit will resist re-mounting.

ON - DEACTIVATE

IMPORTANT! PLEASE READ

CAREFULLY AND SAVE.

The warnings/limitations card and

manual contains important information

about your smoke alarm’s operation. If

you are installing this alarm for use by

others, you must leave this manual—or a

copy of it—with the end user. Reference

product card for additional information.

USER’S MANUAL

SMOKE AND FIRE* ALARM

10-YEAR SEALED BATTERY

OPERATED PHOTOELECTRIC SMOKE

ALARM WITH SILENCE FEATURE

Printed in Mexico

M08-0466-160277-US_RevB L 01/18

Model P1210

CONFORMS TO UL STD 217

INTRODUCTION

Thank you for choosing First Alert

for your smoke alarm needs. You have purchased a state of the

art smoke alarm designed to provide you with early warning of a fire. Please take the time to read

this manual and make the smoke alarm an integral part of your family’s safety plan.

KEY FEATURES OF THE P1210 SMOKE ALARM:

Photoelectric Sensing Technology: Photoelectric Sensors are generally more sensitive than ionization

sensors in detecting smoldering fires which commonly occur in couches or bedding.

OptiPath 360 Technology™: Patented technology provides 360° of direct access to the smoke sensor.

Single Test/Silence Button: Allows you to test the alarm or silence nuisance alarms. Testing the

alarm assures you that the unit is functioning correctly and ready to protect you and your family.

The alarm can be silenced for up to 9 minutes in the event of a nuisance alarm.

10-Year End of Life Indicator and Low Battery Warnings: The alarm will chirp once per minute indicating

a Low Battery Warning, meaning the unit will need to be replaced soon. The alarm will horn 3 pulses every

43 seconds to alert that the batteries are dead and the unit needs to be replaced immediately.

Latching Feature - Alarm Memory: The alarm sensed smoke or fire, went off and pulled itself out of alarm mode.

To notify you of this event, the alarm will give 3 quick flashes every 45 seconds for 24 hours. You can stop it by

pressing the test/silence button. After 24 hours, it will pull itself out of the latch mode and no longer flash.

Low Battery Silence: The alarm can be silenced for 8 hours.

•

BRK Brands, Inc.

is a subsidiary of Newell Brands Inc. (NYSE:NWL)

•

3901 Liberty Street, Aurora, IL 60504-8122

•

Customer Service Team: (800) 323-9005

•

www.firstalert.com

•

www.brkelectronics.com

Installed on Replace by