ELECTRIC SIT-STAND DESK Instruction Manual ｎａｎ＠ｕｐｇ ｒａｄｅｄｅｃｏｒｓｈｏｐ．ｃｏｍ (909)637-7665 | (909)637-7593 EST 9:00AM--17:00PM
1 x1 2 x1 3 x1 4 x1 Beam Left Leg Right Leg Drive Rod 5 x2 6 x2 7a x1 7b x1 Side Plate Leg Base 8 x2 9 x1 Desk Connection Hook Rectangular Board 12 x1 Power Supply 16 x3 Desk Connection Plate 20 x10 Silicone Sheet 13 x1 Hand Controller 17 x1 Cable Hole Cover 21 x8 Hidden Screws Board 10 x4 Square Board 14 x1 Wire Plate Board 11 x1 Board 15 x2 Drawer 18 x22 19 x2 Wooden Pin Cable Clip
M-A x1 Screws M-B x10 M-C Screws x8 Screws 2.5mm M-F x12 Screws M-G x8 M-H Board Screws M-D x14 Screws M-E Screws 5mm x1 Wrench M-I x8 x1 Wrench Screwdriver is required during the installation please prepare it in advance. Step 1 4 M-H M-A 2 Align the holes of Left Leg (2) and Drive Rod (4), using Wrench (M-H) to secure both with Screw (M-A).
Step 2 4 3 Insert Drive Rod (4) into the hole of Right Leg (3). If it cannot be inserted tilt Right Leg (3) slightly until they’re matched. Step 3 2 M-I M-B 1 3 As shown, use Wrench (M-I), install Beam (1) to the Legs (2&3) with Screws (M-B)*6.
Step 4 M-I M-C 6 Using Wrench (M-I), install Leg Base (6)*2 to the Legs (2&3) respectively with Screws (M-C)*8. Step 5 5 M-B M-I Using Wrench (M-I), install Side Plate (5)*2 on each side of the Legs (2&3) with Screws (M-B)*4.
Step 6 20 1 Fix Silicone Sheet (20)*2 to the corresponding position on the Beam (1).
M-D 8 M-D 16 Fix Boards (7a&7b) with Wooden Pin (18)*4. Use screwdriver, with Screws (M-D)*10, install Desk Connection Plate (16)*3 to the middle of the Boards and Desk Connection Hook (8)*2 to both sides of the Boards. Step 8 20 Fix Silicone Sheet (20)*8 to the corresponding hole position on the Boards (7a&7b).
Step 9 M-E 20 Use screwdriver, secure the installed leg part to the Boards (7a&7b) with Screws (M-E)*8. Please align the Silicone Sheet (20)*8. Step 10 1 13 2 2 13 12 As shown, connect the motor at the Left Leg (2), Hand Controller (13) and Power Supply (12) in turn.
Step 11 M-D 13 Using screwdriver, install Hand Controller (13) to the Board (7a) with Screws (M-D)*2. Step 12 14 As shown, fold the Wire Plate (14).
Step 13 M-D 14 Using screwdriver, install Wire Plate (14) to the Board (7b) with Screws (M-D)*2 Step 14 1 19 2 19 3 Put Power Supply (12) into the Wire Plate (14). Secure the connecting cable with Cable Clip (19)*2 and glue it to the bottom of the Board.
Step 15 17 Insert Cable Hole Cover (17) into the hole in the Board (7b). Step 16 9 18 7b Install Rectangular Board (9) to the Board (7b) with Wooden Pin (18)*3.
Step 17 10 18 Install Small Square Board (10)*4 to the Board (7b) with Wooden Pin (18)*4. Step 18 M-F Using screwdriver, secure the installed square boards (9&10) completely with Screws (M-F)*12.
Step 19 11 M-G 11 11 Using screwdriver, fix Board Screws (M-G)*8 to the Board (11). Step 20 11 18 Attach Board (11) to the square boards (9&10) with Wooden Pin (18)*11.
Step 21 Using screwdriver, fix Hidden Screws (21)*8 to the square boards (9&10).
Step 22 Put in Drawer (15)*2.
Using the Controller Raise the Desk Press the v button to raise the desk continuously until it reaches the highest position or the button is released. Lower the Desk Press the v button to lower the desk continuously until it reaches the lowest position or the button is released. Select Height Setting 1 Press the 1 button, and the desk will move to the height that was previously set for that button.
Settings Reset Press and hold the v button until 'rst' is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly. Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won't work until reset is done correctly. Child Lock Press and hold the v and v buttons together for 5 seconds to turn child lock on. The screen will show 'LOC' and the buttons will be disabled. Turn child lock off the same way.
Protection Mode Error Codes SC0 Standby Overvoltage Protection: Standby voltage too high. Power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support. SC1 Power Supply Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
E11 Overloading Protection: Max load exceeded. Error code will persist for 20 seconds (DO NOT operate). Take the things off the desk and confirm there is no mechanical damage before trying again. E12 Motor Phase Error Protection: Power off, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support. E13 Sensor Malfunction Warning: Motor sensor can’t be detected.
Technical Support (909)637-7665 | (909)637-7593 Other Info ｎａｎ＠ｕｐｇ ｒａｄｅｄｅｃｏｒｓｈｏｐ．ｃｏｍ Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don't hesitate to contact us.
