Product Overview

DESCRIPTION

The Fireye MEP560, MEP561, MEP562, MEP564, MEP536 and MEP537 Programmer Modules are used

with the Fireye Modular MicroM control. The operational characteristics of the control are determined by

the selection of the programmer module (e.g. re-light, 2-stage capability, pilot cutoff, etc.). The program-

mer module incorporates a plug-in design for easy installation.

These programmer modules are equipped with a series of dipswitches to select Purge Timing, Pilot Trial

for Ignition (PTFI) Timing, Air Flow Proven Open at Start, Post Purge and Recycle or Non-Recycle oper-

ation. LED indicator lights are on all programmer modules, indicating the operating status of the control

as well as providing diagnostic codes during lockout. A check/run switch is provided to assist in testing

size and stabilization of the pilot.

Flame Failure Response Time (FFRT) is determined by the selection of the amplifier module. Test jacks

are also provided on the flame amplifier module to permit flame signal measurement during operation.

For proper and safe application of this product, you must refer to Fireye bulletin MC-5000 for a detailed

description of the various programmer modules, including installation instructions, amplifier selection,

operating sequences for each programmer module, etc.

WARNING: Selection of this control for a particular application should be made by a competent

professional, licensed by a state or other government agency. Inappropriate application of this

product could result in an unsafe condition hazardous to life and property. Installation should not

be considered complete until pilot turndown and other appropriate performance tests have been

successfully completed.

PROGRAMMER MODULE SELECTION

WARNING: Remove power from the control and remove the control from its wiring base

before proceeding.

MicroM Programmer Models (For use with MEC120 and MEC230 Chassis)

MEP560 Provides dip switches to select purge time (7, 30, 60, 90 seconds), 5/10 second PTFI, Air Flow Proven Open at Start, Post

Purge, Recycle or Non-recycle. Provides 8 second pilot stabilization period and 10 second main trial for ignition. Run/check

switch included.

MEP561 Same as MEP560 without 8 second pilot stabilization. Selectable purge time of 7, 10, 15, 30 seconds.

MEP562 Same as MEP560, lockout on loss of air flow, non-recycle operation only.

MEP564 Same as MEP560. Selectable purge time of 7, 30 ,60, 240 seconds.

MEP536 Same as MEP560 without pilot stabilization period. Will not lockout on air flow open during purge period.

MEP537 Same as MEP536 except provides one recycle on main flame failure.

MEP560, MEP561, MEP562,

MEP564, MEP536, and MEP537

PROGRAMMER MODULES

FOR USE WITH THE FIREYE

MODULAR

MicroM™ CONTROL TO BE USED

WITH MEC120 AND MEC230 CHASSIS

MP-5501

APRIL 3, 2013

APPROVED

PAGE 1
® MP-5501 APRIL 3, 2013 MEP560, MEP561, MEP562, MEP564, MEP536, and MEP537 PROGRAMMER MODULES C US APPROVED FOR USE WITH THE FIREYE® MODULAR MicroM™ CONTROL TO BE USED WITH MEC120 AND MEC230 CHASSIS DESCRIPTION The Fireye MEP560, MEP561, MEP562, MEP564, MEP536 and MEP537 Programmer Modules are used with the Fireye Modular MicroM control. The operational characteristics of the control are determined by the selection of the programmer module (e.g. re-light, 2-stage capability, pilot cutoff, etc.).
PAGE 2
 INSTALLATION The Programmer Modules are used with the Fireye modular MicroM Chassis (P/N MEC120, MEC120RC, MEC120R, MEC120D, MEC120RD and MEC120C for 120VAC and MEC230 for 230 VAC). They are installed in the chassis by grabbing hold of the programmer module by the ridged finger grips on the side on the module, aligning the module with the guide slots on the opening farthest from the transformer, and inserting the module into the pin connectors.