Brochure

ManualsBrandsFireye ManualsHeating Supplies10 Sec. PTFI MicroM Non-Recycle Programmer Module without Pilot Stabilization

FIREYE PRIMELINE PRODUCTS • 31

MicroM SERIES Bulletins MC-5000, MAMP-1, MOPT-1, MP-5201, UM-2

The Fireye MicroM Flame Safeguard controls are compact, modular

burner management systems designed to provide automatic ignition and

continuous flame monitoring for commercial sized heating and process

burners firing any type of fuel. The MicroM is designed to be backward

compatible with existing M-Series controls. The MicroM, through the use

of micro-controller technology, incorporates “smart” diagnostic LED’s,

optional alphanumeric display (ED510), remote reset capability, and serial

communications via MODBUS or E500 Communication Interface. These

options are available through plug-in option boards to the chassis. The

optional ED510 display can be utilized to access burner hours and cycles,

system hours, the last 6 lockouts with burner cycle time stamp and pro-

grammer configuration. The optional MODBUS communications capabil-

ity allows the integration of the MicroM control into upper level energy

management / data acquisition systems.

A complete MicroM system consists of the appropriate flame scanner/detector, plug-in amplifier and programmer modules connected into a

standard chassis and wiring base. Interchangeable programmer and amplifier modules allow complete versatility when selecting control

function, timing, and flame scanning method. Functions such as relight, two-stage capability, purge timing, and pilot cutoff are determined

by the programmer module. Type of flame scanner (UV, UV self check, infrared, flame rod, photocell, and cadmium cell) and Flame Failure

Response Time (FFRT) are determined by the amplifier module. All amplifiers are available with flame failure response times of 0.8 seconds

or 3 seconds nominal (4 seconds max), and each provide a set of test jacks with a range of 0-10 VDC for the measurement of flame signal

intensity.

Some programmer modules (MEP200 and MEP500 series) have dipswitches for selecting purge timing, pilot trial-for-ignition (PTFI) timing,

recycle or non-recycle operation, prove air flow open at start, and post purge. Smart LED indicators on all of the programmer modules indi-

cate the current operating status of the control and, during a safety lockout, display the fault as a coded sequence, simplifying the trouble-

shooting of a shutdown. A “run-check” switch is provided on the MEP500 series programmers to assist in testing the size, position, and

stability of the pilot. The MicroM control incorporates a safety checking circuit that is operative on each start. If flame (real or simulated) is

detected prior to a start or during purge, the fuel valves will not be energized and the control will lockout.

DIMENSIONS

PART NUMBER MicroM Chassis Types for use with MEP100, 200 and 500 series programmers

MEC120 120 VAC input with standard plug-in board

MEC120R 120 VAC input with remote reset capability

MEC120D 120 VAC input with alpha-numeric display interface to ED510

MEC120C 120 VAC input with interface to E500 Communication Interface and Modbus capability.

MEC120RC 120 VAC input with remote reset capability, alpha-numeric display interface to ED510, interface to E500 Communication Interface

and Modbus capability

MEC120RD

120 VAC, 50/60 Hz Chassis with remote reset capability and interface to ED510.

MEC230RC 230 VAC, 50/60 Hz Chassis with remote reset capability, interface to ED510, interface to E500 Comm. Interface, and

Modbus capability.

MEC230 230 VAC input with standard plug-in board.

5 3/16”

MOUNTING BASE

5 5/16”

4”

1/2’

1/2”

3/16” DIA. MOUNTING

HOLES (4)



KNOCKOUTS

(12)

FOR 1/2”