Instructions / Assembly

ManualsBrandsFireboy-Xintex ManualsBoat Docks & HardwareDual Channel Propane Fume Detector with Solenoid Valve Control

Part Number 18143, D, 11/07/2017

Propane Fume Detection System

With Solenoid Valve Control

Single Channel Systems

P-1BS-R (Black, Round, Solenoid Control)

P-1CS-R (Chrome, Round, Solenoid Control)

Dual Channel System

P-2BS-R (Black, Square, Solenoid Control)

Owner’s Manual

Installation Instructions

Read and comply with all instructions, warnings and limitations before

installing, servicing or removing this device.

Summary of content (9 pages)

PAGE 1
Propane Fume Detection System With Solenoid Valve Control Single Channel Systems P-1BS-R (Black, Round, Solenoid Control) P-1CS-R (Chrome, Round, Solenoid Control) Dual Channel System P-2BS-R (Black, Square, Solenoid Control) Owner’s Manual & Installation Instructions Read and comply with all instructions, warnings and limitations before installing, servicing or removing this device.
PAGE 2
Additional copies of this manual are available at no charge by contacting the manufacturer, distributor or dealer. Fireboy-Xintex reserves the right to change features without notice.
PAGE 3
General Information WARNING PROPANE FUME DETECTORS ARE MEANT TO SERVE AS A SUPPLEMENTAL WARNING SYSTEM. IT IS NOT MEANT TO REPLACE STANDARD SAFETY PRACTICES WHICH SHOULD BE CARRIED OUT AROUND EXPLOSIVE GASES. The P-1BS-R, P-1CS-R, and P-2BS-R Propane Fume Detectors are an effective means to monitor propane fumes in a compartment or leaking fuel systems. In addition, these units have the ability to control the flow of CNG/LPG to your appliances.
PAGE 4
Operation of Xintex Propane Fume Detector(s) There are 3 LEDs located on the Display Unit for each channel on the system, as well as an LED for the Solenoid Valve status. The Green LED, located at the top, indicates that the system is operational. The Yellow LED, located in the center, indicates that there is a Fault in the system. This is to notify the user to check the connections and wire runs of the sensors. There may be a break in the wiring or a disconnected sensor on that channel.
PAGE 5
Part Number 18143, D, 11/07/2017 P2BS-S01-D P1BR-S01-D P1CR-S01-D FS-X01 CABLE XX’ Solenoid Valve FS-X01 CABLE XX’ YELLOW – Switching Ground 2A Fuse Included Solenoid Valve FS-X01 CABLE XX’ +12 VDC From Solenoid Circuit Breaker (2A) (May be obtained @ Display Unit. 2A fuse recommended) FS-T01 FS-T01 +12 VDC From Solenoid Circuit Breaker (2A) (May be obtained @ Display Unit. 2A fuse recommended) FS-T01 RED – Power (+) 1.
PAGE 6
Installation Installing the Display Unit (P1BR-S01-D/P1CR-S01-D & P2BS-S01D) The Display Unit should be located at the instrument panel, so that the visible and audible indicators may be easily observed. Drill a 2-1/16” hole to accommodate the P1BR-S01-D/P1CR-S01-D Display Unit. Drill a 2-1/8” hole to accommodate the P2BS-S01-D Display Unit. Insert Display Unit into hole and secure with the provided threaded mounting nut. NOTE DO NOT MAKE ELECTRICAL CONNECTIONS AT THIS TIME.
PAGE 7
Installation Continued Installing Propane Fume Sensor(s) (FS-T01) The Propane Fume Sensor should be located by the propane powered appliance, near the floor. Avoid areas where damage may take place due to cleaning, mopping, kicking, or other physical damage. Harsh chemicals should not be used to clean sensors. Use the appropriate #8 mounting hardware to mount the Propane Fume Sensor in the desired location. The rubber gasket should be installed between the sensor and the mounting surface.
PAGE 8
Testing the Propane Fume Sensors WARNING DO NOT USE A PROPANE SOAKED RAG OR A PARTIALLY FULL CONTAINER OF PROPANE TO TEST A SENSOR. THE RAW PROPANE COULD IGNITE, RESULTING IN SERIOUS INJURY. Test the Sensors by holding a Butane lighter to the sensor. Within a few seconds, the Red “Danger” LED should illuminate and the alarm horn will sound. Remove the lighter from the Sensor and mute the alarm horn. After approximately one minute, the Red LED will shut off.
PAGE 9
1 Year Limited Warranty This Warranty is in lieu of all other expressed or implied Warranties Seller warrants title, materials, and workmanship on equipment, except components manufactured by others for which the Seller assigns, as permitted, the original manufacturer’s warranty.