Outdoor Patio Heater INFRARED BURNER Model # LIP-09A-TGG Item # 62224 WARNING ATTACH YOUR RECEIPT HERE Serial Number ___________ Manufacturer: Changzhou Wellife Furnace Co., Ltd. This product can expose you to chemicals including carbon monoxide which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
TABLE OF CONTENTS Table of Contents………………………………….....................Page 2 Before You Begin............................................................Page 2 Safety Information.........................................................Page 3-4 Package Contents………………………………….....................Page 5 Hardware Contents..........................................................Page 6 Assembly.........................................................................Page 6-11 Operating Instructions…………….....
SAFETY INFORMATION 3
SAFETY INFORMATION 4
PACKAGE CONTENTS ASSEMBLY PART DESCRIPTION QTY A Top Cap 1 B Reflector 1 C Emitter 1 D Upper Supports 4 E Lower Supports 4 F Mesh Guards 8 G Glass Tube Connector 1 H Glass Tube 2 pcs I Burner 1 J K L 5 Tank Housing/Base Assembly (with wheels) Regulator/Hose assembly Cylinder Holder 1 1 1
HARDWARE CONTENTS ASSEMBLY INCLUDED IN PLASTIC BAG WITH INSTRUCTION MANUAL INCLUDED IN BLISTER PACK ASSEMBLY PREPARATION Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package contents list and hardware contents as listed on pages 2 and 3 of this manual. If any part is missing or damaged, do not attempt to assemble this product. Contact customer service for replacement parts.
ASSEMBLY 1. Locate 4 pieces of Upper Supports and 4 pieces of Lower Supports. Slide 1 - Mesh Guard Connector over bottom end of Upper Support, then screw Upper Support onto Lower Support (Note: Mesh Guard Connector will remain loose and able to slide on the supports.) Repeat with remaining Upper and Lower Supports and Mesh Guard Connectors until you have 4 assembled Supports. Hardware Used: 4 x D, Mesh Guard Connector 1 2. Attach the assembled Supports to the Tank Housing/Base Assembly.
ASSEMBLY 3. Fit the Emitter (C) down over the threaded end of the assembled Supports by 3 lining up the holes in the corners of the Emitter with the Supports and sliding the Emitter down over the Supports. 4. Secure the Emitter to the Supports using 4 pieces of B - M8 Spacer. Tighten with an open end wrench.
ASSEMBLY 5 5. Attach Reflector (B) to top of Supports. Align holes in bottom of Reflector with Supports and slide Reflector down over Supports. 6 6. Secure Reflector to Supports with 4 pieces A - M8 Nut. Tighten with an open end wrench. Hardware Used: 4 x A, M8 Nut 7 7. Place Top Cap (A) into Reflector.
ASSEMBLY 8 8. Assemble Glass Tube. Locate Glass Tube Connector (G) and two pieces of Glass Tube (H). Carefully insert one end of Glass Tube Connector into open end of Glass Tube and then repeat with other Glass Tube. 9. Insert Glass Tube into Emitter and Tank Housing/Base Assembly. Carefully insert assembled Glass Tube into end of Emitter and then into hole on top of the Tank Housing/Base Assembly. 10 10. Attach Mesh Guards to Supports. Hint: It is best to begin with bottom pieces of Mesh Guards.
ASSEMBLY 11. Before placing LP tank onto base of heater, attach Cylinder Holder (K) 11 to base using 3 pieces of M6x12 Bolts. Hardware Used: 3 x C, M6x12 Bolt Connect the Regulator/Hose assembly to the LPG cylinder. The LPG cylinder is sold separately. Use a standard 20 lb. LPG cylinder only. Screw the Regulator/Hose assembly to the LPG cylinder. Do not cross thread. Hand tighten securely. Then attach the Regulator/Hose assembly to the end of the hose that extends from the Burner. Do not cross thread.
OPERATING INSTRUCTIONS Leak Test 1. 2. 3. 4. 5. Make 2-3 oz. of leak test solution (one part liquid dishwashing detergent and three parts water). Apply several drops of solution where hose attaches to regulator. Apply several drops of solution where regulator connects to cylinder. Make sure all patio heater valves are OFF. Turn cylinder valve ON. IF BUBBLES APPEAR AT ANY CONNECTION, THERE IS A LEAK. 1. Turn cylinder valve OFF. 2.
OPERATING INSTRUCTIONS Before Lighting: 1. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. If re-lighting a hot heater, always wait at least 5 minutes. 2. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by the manufacturer.
OPERATING INSTRUCTIONS Operation Checklist: For a safe and pleasurable heating experience, perform this check before each use: Before Operating: 1. I am familiar with entire owner’s manual and understand all precautions noted. 2. All components are properly assembled, intact and operable. 3. No alterations have been made. 4. All gas connections are secure and do not leak. 5. Wind velocity is below 10 mph. 6. Unit will operate at reduced efficiency below 40 degrees F. 7.
Heater makes popping noise. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if any carbon deposits develop. Always be careful when cleaning the glass tube.
TROUBLESHOOTING If you have any questions regarding this product, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net. PROBLEM Main burner will not light Low burner flame POSSIBLE CAUSE CORRECTIVE ACTION Gas valve may be off Turn gas valve ON Fuel tank may be empty Refill LPG tank Orifice blocked Clean or replace orifice Air in supply system Purge air from lines.
REPLACEMENT PARTS LIST ASSEMBLY For questions regarding this product or to purchase replacement parts, please call our customer service hotline at 1-866-985-7877, 9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net.
Distributed By: Well Traveled Living 716 S 8th Street Amelia Island, FL 32034 Toll Free: 866-WTL-SUPP (866-985-7877) Web: www.wtliving.com Email: cservice@welltraveled.net 1 YEAR LIMITED WARRANTY – Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use.
