Patio Heater Model: PH01-S PH01-SS Item numbers: 61185 WARNING: For outdoor use only. FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, immediately call gas supplier. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. PLEASE retain this manual for reference. CERTIFICATE TO ANSI 83.26a-2008 CONFORM TO CSA 2.
Tools and parts needed for assembly DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car or home. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
PRECAUTIONS NOTE: PLEASE READ THE FOLLOWING SAFETY RULES WARNING: This heater must only be used outdoors. Using this product in an enclosed area may cause injury, death or property damage. Only use in a well-ventilated space. Do not use in a building, garage, or any other enclosed area. Read the instructions before use. This heater must be installed in accordance with local codes or, in the absences of local codes, with the National Fuel Code, ANSI Z223.1.
PRECAUTIONS CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING EXIST: 1. The smell of gas in conjunction with extreme yellow colored tips of the burner flames. 2. The heater does not reach temperature. 3. The burner makes a popping noise during use (a slight popping noise is normal when the burner is extinguished after using). Children and adults should be aware of the hazards of high surface temperature, and should stay away to avoid burns or clothing ignition.
ASSEMBLY 1. 3 pcs castle nuts 2. Reflector 3. 6 pcs 8mm washers for pins support 4. 3 pcs 90mm (L) pins for reflector support 5. Head assembly 6. 4 pcs M6x10mm bolts 7. 2 pcs Post assembly 8. Tank housing 9. Regulator 10. 6 pcs M6x30mm bolts and M6 washers and 6mm nuts for connection of post support and support legs 11. 3 pcs M8x16mm bolts for connection of support legs and base 12. Post support 13.
ASSEMBLY Step 1 ATTACHING WHEEL ASSEMBLY 1-1. Locate Wheel Assembly (17) and 2 nuts/bolts contained in plastic bag with Wheel Assembly (Fig. 1). Fig. 1 Step 2 2-1. Turn Base (15) so that holes for attachment of Wheel Assembly are facing you (Fig. 2). Fig. 2 2-2. Align holes in Wheel Assembly (17) with holes on Base (15) (Fig. 3).Insert bolts through both sets of holes and secure nuts on end of bolt (Fig. 4). Fig. 3 Fig. 4 Step 3 3-1.
ASSEMBLY WARNING: This appliance requires installation by a competent person. Proper assembly is the responsibility of the installer. Step 1 1-1. Attach 3pcs LPG cylinder fixed parts on the base with 6pcs M6x12mm bolts and M6 washers and 6mm nuts. 1-2. Position the 3 pcs support legs on the base as shown in the picture to the right. 1-3. Use 3 pcs M8x16mm bolts to affix the support legs to the base. Step 2 2-1. Put the post support on top of the 3 pcs support legs. 2-2.
ASSEMBLY Step 3 3-1. Connect the second piece of the post assembly to the first piece of the post assembly and screw on clockwise. Step 4 4-1. Place the tank cover on the base. Step 5 5-1. Secure the 3 pcs 90mm pins(reflector support bolts) on the cap of emitter screen. 5-2. Route the gas hose down through the post and out of the bottom. 5-3. Connect the regulator with gas hose. 5-4.Fix the head unit collar to the post with 4 pcs. M6x10mm bolts.
ASSEMBLY Reflector (#2) is comprised of 3 – outer pieces and 1 – center piece. Locate all 4 pieces of Reflector (#2) which are wrapped in bubble wrap. Unwrap and remove all pieces and peel off the protective blue plastic on each piece. Locate 9 bolts and 9 cap nuts in the plastic bag. Align the 3 – outer pieces with the 1 – center piece and place a bolt through the center hole on each piece as shown below. Tighten castle nut on each bolt.
ASSEMBLY Step 6 6-1. Put 8mm washer on each reflector support bolt. 6-2. Fasten the reflector with 3 pcs washers and 3 pcs M8 mm castle nuts. Step 7 7-1. Lift the tank cover and rest it on the post flange. 7-2. Connect the other end of gas hose with regulator to the gas cylinder and tighten. Warning: When connecting the gas cylinder and regulator, make sure the connection is tight and always check for any leaks. Please see page 11 “Check for Leak” for full instructions. 7-3.
ASSEMBLY 7-4. Lower tank over gas cylinder and down to cover base. Check for Leak Your patio heater has been checked at all factory connections for leaks, but you should always check when you attach the LPG cylinder. To check for leaks, following these instructions: --Assemble all gas connections; --Connect regulator assembly to the propane tank; --Make sure the heater valve is turned OFF. 1) Make soapy solution by mixing 1 part liquid dish soap and 3 parts water. 2) Open the propane tank valve.
ASSEMBLY 8) If bubbles still appear, close the propane tank valve and contact your gas supplier. If a leak is detected , DO NOT attempt to use the heater. MAKE SURE to check all THREE connections between the cylinder and gas line. NOTE: 1) The cylinder must be provided with a shut off valve terminating in a LPG supply cylinder valve outlet specified, as applicable, for connection NO 510 in the standard for compressed gas cylinder valve outlet and in let connections, ANSI/CGA-v-1.
ASSEMBLY C. Spoon several drops (or use squirt bottle) of the solution onto gas hose connection and pilot connection. D. Inspect the connections and look for bubbles. E. If no bubbles appear, the connection is safe. F. If bubbles appear, there is a leak. Close the propane tank valve and loosen and re-tighten this connection. G. Check for leaks again. H. If bubbles still appear, close the propane tank valve and call the gas supplier. DO NOT attempt to use the heater.
OPERATION LIGHTING INSTRUCTIONS TO TURN ON THE HEATER: 1. Turn the control knob “OFF”. 2. Open gas valve fully. 3. Press and turn the control knob to “HI” position (counterclockwise 90° ). Press down the control knob and hold 3-5 seconds. While holding down the control knob, press the igniter button several times until the pilot flame ignites. Hold the knob about 30 seconds and then release. Note: If the pilot flame does not light or it goes out, repeat Step 3 above.
OPERATION CAUTON: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should not produce thick black smoke. Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the “LO” position, then turn the knob to the level of heat desired.
LOCATION OF HEATER WHILE IN USE CAUTION: WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. This heater is to be used for the heating of outdoor patios, decks, spas, pool, and open working areas. This heater is for OUTDOOR use ONLY. Always make sure that adequate fresh air ventilation is provided and follow the spacing tolerances shown in the picture below. The minimum clearances must be maintained at all times.
MAINTENANCE CLEANING AND MAINTENANCE To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance on a regular basis: Keep exterior surfaces clean. WARNING FOR YOUR SAFETY DO NOT touch or move heater for at least 45 minutes after use. Allow all burner elements to cool before touching. 1. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. 2.
TROUBLESHOOTING Problem Problem cause Burner will not light Pressure is low Fuel tank is near empty Control valve not ON Turn valve to ON Thermocouple bad Replace thermocouple Pilot light assembly bent or not in correct location Place pilot in proper position and retry Supply hose is bent or twisted Straighten hose and perform leak test on hose Blockage in burner injector Low gas pressure Clean or replace burner injector Let the pilot flame stay lit for 10 minutes before setting variable knob
Distributed By: Web: www.wtliving.com Well Traveled Living 716 S 8th Street Email:cservice@welltraveled.net Amelia Island, FL 32034 Toll Free: 866-WTL-SUPP 1 YEAR LIMITED WARRANTY – Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use. This warranty does NOT cover normal wear and weathering, assembly and/or maintenance OR use in a commercial application.
