Quick Start Guide

REV 1 - 1602081000
L-C2-407
4-Grill Setup
Fig. 4-1
Cooking grid
Flavor grid
(not with IR)
Backburner
cover
Warming
rack
Cotter
pin
Rotisserie
rod storage
ring
6-Propane Safety
Gas Cylinders
IMPORTANT: READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
READ ALL SAFETY INSTRUCTIONS AND WARNINGS REGARDING THE USE OF PROPANE GAS FOUND IN
YOUR OWNER’S MANUAL.
Sideburner
lid
Parts Placement Checklist
Place the following items according to their position and orientation in
Fig. 4-1:
Flavor grids, cooking grids, heat zone dividers, backburner cover,
warming rack, and meat probe.
Leave pre-installed E-burners in place to maintain proper alignment.
Backburner Cover
Hook the backburner cover over the top of the backburner to protect
the backburner from grease, dust and dirt when it is not in use. Remove
before use.
Warming Rack
The warming rack comes pre-installed. Remove zip ties before use.
Consult the owner’s manual to remove or replace.
Shelf/Sideburner (if equipped)
Align the four (4) holes in the shelf with the four (4) holes in the side of
the cart while aligning and engaging the burner venturi with the orifi ce
(Fig. 4-2). Insert the four (4) screws (provided) into the holes and tighten.
Connect the spark wire to igniter electrode (Fig. 4-2). Open sideburner
lid, set cap on burner, and set grid into shelf.
Screws
Igniter
electrode
Air shutter
Orifi ce
Spark
wire
Fig. 4-2
Venturi
Note: For infrared burner equipped
grills; see detailed instructions
included in your owner’s manual.
Fig. 5-2
Left main burner
control knob
Right
main burner
control knob
Center right main burner
control knob
Center left main
burner
control knob
Smoker drawer
burner control
knob
Right backburner
control knob
(if equipped)
Left
backburner
control knob
(if equipped)
Pull-out drip
tray
Smoker
drawer
Drip tray
liners
Drip tray (with
lighting instructions)
5-Test
Note: This unit must be connected to 120VAC power for electronic lighting.
1. Open lid(s) or remove cover(s) from burner(s) to be lit.
2. Turn all gas control knob(s) to their OFF position(s).
3. Turn on the gas at its source.
Note: DO NOT turn on more than one valve at a time for either electronic or manual lighting.
4. Depress the desired control knob for 5 seconds, then, while pressing turn it counterclockwise to the
HI LIGHT position. Once the burner lights, release the knob.
CAUTION: If a burner does not light within fi ve (5) seconds of turning on the control knob, depress
the knob and turn it to the OFF position. WAIT FIVE (5) MINUTES before repeating
step 4. If you smell gas, follow the instructions on the cover of the grill owner’s manual.
If the burners still do not light after several attempts, refer to the grill owner’s manual
for manual lighting.
5. Repeat step 4 for each additional burner to be lit.
Door
Drawers
Sideburner
control knob
WHEN OPERATING THIS
APPLIANCE WITH PROPANE, ALL
INSTRUCTIONS AND WARNINGS
MUST BE OBSERVED. FAILURE TO
DO SO MAY RESULT IN A FIRE OR
EXPLOSION CAUSING SERIOUS
INJURY OR DEATH.
For your convenience and safety;
when the control knob is in the
ON position, the gas fl ow indicator
will change from blue to red. (Red
indicates gas fl ow.) See Fig. 5-1.
Fig. 5-1 - Burner valve control knob
OFF
HI
LIGHT
LOW
TO
TURN OFF
T O TURN ON
Read setting
here
HIGH to
LIGHT
Read setting here
(OFF position shown)
To Turn OFF
To Turn ON
Use
HI (high)
to light
Press
knob in
to turn
Gas Flow
Indicator
Light
switch
E-burner
*
(comes pre-
installed)
*
The burner ports
and carry-over slots
must be kept clean to
ensure proper ignition
and operation.
The light switch is push button operated,
and is located on the right side of the
control panel (see Fig. 5-2). It controls the
power to all lights.
Replacement parts can
be ordered from your
local Fire Magic dealer.