User Manual
Document #51123 Rev. A ECN 98-542 1/8/99
WW
WW
W
ARNING!ARNING!
ARNING!ARNING!
ARNING!
Do not allow trouble conditions to remainDo not allow trouble conditions to remain
Do not allow trouble conditions to remainDo not allow trouble conditions to remain
Do not allow trouble conditions to remain
logged in the system. Protection that thelogged in the system. Protection that the
logged in the system. Protection that thelogged in the system. Protection that the
logged in the system. Protection that the
system offsystem off
system offsystem off
system off
ers has been compromised, orers has been compromised, or
ers has been compromised, orers has been compromised, or
ers has been compromised, or
eliminated when a trouble condition exists.eliminated when a trouble condition exists.
eliminated when a trouble condition exists.eliminated when a trouble condition exists.
eliminated when a trouble condition exists.
Frame and mount adjacent to the control panel.
411UD411UD
411UD411UD
411UD
AA
AA
A
C DigC Dig
C DigC Dig
C Dig
ital Commital Comm
ital Commital Comm
ital Comm
unicaunica
unicaunica
unica
tortor
tortor
tor
OperOper
OperOper
Oper
aa
aa
a
ting Instrting Instr
ting Instrting Instr
ting Instr
uctionsuctions
uctionsuctions
uctions
NORMAL NORMAL
NORMAL NORMAL
NORMAL - Only the green AC POWER LED is on. All other
LEDs are off.
PP
PP
P
ANELANEL
ANELANEL
ANEL - The key to open the panel can be found at this
location.
WHEN AUDIBLE DEVICES ARE SOUNDING -WHEN AUDIBLE DEVICES ARE SOUNDING -
WHEN AUDIBLE DEVICES ARE SOUNDING -WHEN AUDIBLE DEVICES ARE SOUNDING -
WHEN AUDIBLE DEVICES ARE SOUNDING -
FF
FF
F
or an Alaror an Alar
or an Alaror an Alar
or an Alar
m:m:
m:m:
m:
1) Evacuate the protected area.
2) Notify the monitoring service and/or the Fire Department
immediately. Tell them briefly what happened and what
your current status is.
3) If the Fire Department is responding, be prepared to
provide directions to arriving firefighters.
FF
FF
F
or or
or or
or
TT
TT
T
roubroub
roubroub
roub
le Only:le Only:
le Only:le Only:
le Only:
1) Notify the monitoring service and/or Fire Department if this
panel is connected to either one, and tell them what is
happening.
2) Silence audible devices by unlocking and opening the
panel and pressing the ACK/SILENCE key once. The
yellow TROUBLE LED will remain on. Contact authorized
service personnel immediately! (Refer to Local Service
Representative block below).
TT
TT
T
o returo retur
o returo retur
o retur
n to norn to nor
n to norn to nor
n to nor
mal after an alarmal after an alar
mal after an alarmal after an alar
mal after an alar
m:m:
m:m:
m:
1) Do not enter the protected area until safe to do so.
2) Clear all initiating devices. Smoke detectors will realarm if
there is still smoke in the area.
3) Reset the control panel being monitored by the 411UDAC
or, if being used as a stand-alone fire alarm communicator
(with approval of Authority Having Jurisdiction), press the
411UDAC RESET key.
AlarAlar
AlarAlar
Alar
m Silencingm Silencing
m Silencingm Silencing
m Silencing - Notification Appliance circuit may be
silenced by pressing the ACK/SILENCE key a second time,
holding it for a minimum of two seconds. Subsequent alarms
will reactivate circuits. Press the RESET key to clear the
silenced condition.
NOTE: Alarm silencing may be disallowed for 1 minute if
programmed (see manual).
Power failure or brownoutPower failure or brownout
Power failure or brownoutPower failure or brownout
Power failure or brownout - AC POWER LED will extinguish
for AC fail or brownout and the SYSTEM TROUBLE LED will
turn on. The local panel sounder and SYSTEM TROUBLE
LED will turn on for either condition and any other audible
trouble devices will sound. Contact authorized service
personnel immediately. (Refer to Local Service Representa-
tive block to the right).
Refer to the 411UDAC Technical Manual
P/N 51073 for more details.
Local Service RepresentativeLocal Service Representative
Local Service RepresentativeLocal Service Representative
Local Service Representative
Name:_________________________
Address:_______________________
Telephone:_____________________
To test the lamps, connect the optional
Fireā¢Watch 411 Series DACT Programmer
(Model PRO-411) and press:
LAMP
TEST
INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONSINSTRUCTIONS
INSTRUCTIONS
To clear alarm indications in 411UDAC
after cause of alarm has been corrected,
reset the control panel being monitored by
the 411UDAC.
If 411UDAC is being used as a fire alarm
control panel (with the permission of the
Authority Having Jurisdiction), clear alarm
indications in the 411UDAC by pressing :
To silence the local panel sounder, press:
ACK/SILENCE
RESET
To silence the 411UDAC Notification
Appliance Circuit, press:
ACK/SILENCE
a second time and hold a
minimum of two seconds.