Datasheet

ManualsBrandsFinisar ManualsNetworkingFTL-8519-3D-2.5

Finisar

Product Specification

RoHS Compliant 2.125 Gb/s Short-Wavelength GBIC Transceiver

FTL-8519-3D-2.5

Product Features

• Up to 2.125 Gb/s bi-directional

data links

• 850nm VCSEL Laser

Transmitter

• Optional Digital Diagnostics

Functions

• Extended Operating Temperature

Range (-10°C to +85°C)

• Compatible with 3.3V & 5V

Systems

• Hot-Pluggable (complies with

GBIC specification Rev. 5.5)

• Fully metallic enclosure for low

EMI

• Low power dissipation

• RoHS compliant and Lead Free

Applications

• 1.25 Gb/s 1000BASE-LX

Ethernet

• Dual Rate 1.06 / 2.125 Gb/s

Fibre Channel

Finisar’s FTL-8519-3D-2.5 850nm GBIC transceivers comply with GBIC Specification

Revision 5.5

. They are compatible with the Gigabit Ethernet as specified in IEEE Std

802.3

, Fibre Channel FC-PH, PH2, PH3

and FC-PI-2 Rev. 10.0

. They are RoHS

compliant and lead-free per Directive 2002/95/EC

and Finisar Application Note AN-

2038

Summary of content (9 pages)

PAGE 1
Finisar Product Specification RoHS Compliant 2.125 Gb/s Short-Wavelength GBIC Transceiver FTL-8519-3D-2.5 Product Features • Up to 2.125 Gb/s bi-directional data links • 850nm VCSEL Laser Transmitter • Optional Digital Diagnostics Functions • Extended Operating Temperature Range (-10°C to +85°C) • Compatible with 3.3V & 5V Systems • Hot-Pluggable (complies with GBIC specification Rev. 5.
PAGE 2
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 I. F i n i s a r Pin Out Pin Name Pin # Sequence RX_LOS 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 TX_FAULT (not supported) GND 10 2 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Table 1.
PAGE 3
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 II. F i n i s a r Electrical Power Interface Finisar FTL-8519-3D-2.5 GBICs have an extended power supply voltage range of 3.15 V to 5.5 V as described in Table 2. They are compatible with both 3.3V and 5 V systems. +5/3.3 Volt Electrical Power Interface Parameter Supply Current Surge Current Symbol Is Isurge Min Absolute Supply Voltage Vmax -0.3 Operating Supply Voltage Vcc 3.15 Typ 190 3.
PAGE 4
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 F i n i s a r Low Speed Signal Parameters Parameter Symbol RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay Min Typ --30 --0.
PAGE 5
F i n i s a r FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 V. Optical Parameters Optical Parameters Parameter Transmitter Center Wavelength Transmitter Spectral Width (RMS) Transmitter Optical Output Power Transmitter Extinction Ratio Relative Intensity Noise Transmitter Eye Opening Total Transmitter Jitter Symbol λc Δλ Pout ER RIN -- Min 820 Typ 850 0.5 -9.5 9 -117 60 TJTX Transmitter Rise/Fall Time Optical Input Wavelength Optical Receiver Sensitivity <=1.
PAGE 6
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 F i n i s a r VII. Environmental Specifications Environment Parameter Operating Temp Relative Humidity Storage Temp Eye Safety Symbol Min Top RH Tsto -- -10 0 -40 Typ Max 85 85 85 Units Notes/Conditions °C % °C Case Temperature Non Condensing CDRH and IEC-825 Class 1 Laser Product. See Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No.
PAGE 7
F i n i s a r FTL-8519-3D-2.5 2.
PAGE 8
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 X. F i n i s a r Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61. Figure 1. GBIC Outline Drawing © Finisar Corporation November 16, 2007 Rev.
PAGE 9
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007 F i n i s a r XI. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer Company et. al., September 27, 2000. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3. IEEE Standards Department, 2002. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 4. Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev.