206 Wembly Road New Windsor, NY 12553 Phone: 718.602.6060 Fax: 718.963.2082 info@finefixtures.com www.finefixtures.
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED, COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
PARTS COMPONENTS AND HARDWARE A B C D F G E H During unpacking the product and prior to installation inspect your new product for any damages or missing parts. Do not attempt to install or operate the product if the product is damaged.
1 ATTACHING THE BASE Attach the base to the floor of the shower area.
2 L PREPARING THE FIRST FIXED GLASS PANEL 2.1 Attach the plastic seal strip (L) to the side of the fixed glass panel (J), as shown. 2.2 Attach the door joints (H) to one side of the panel (over the seal), using screws included with the door joints. J I 2.3 Attach the door joints (I) to the other side of the panel, to which the door will be attached. H 2.1 2.2 2.
3 ATTACHING THE FIRST FIXED PANEL 3.1 Use a pencil to mark the screw points in the wall, based on the location of the joints (H). 3.2 Use a size 6 drill bit to drill holes at the marked points. Insert the wall anchors (G) into the holes. 3.3 Attach the joints to the wall with screws (F). 3.4 Attach the joints to the door using screws included with the joints. 3/4” 3.1 3.2 6 3.3 3.
4 L PREPARING THE SECOND FIXED GLASS PANEL B 4.1 Attach the plastic seal strip (L) to the side of the fixed glass panel (B), as shown. 4.2 Attach the door joints (H) to one side of the panel (over the seal), using screws included with the door joints. 4.3 Attach the seal (C) to the other side of the panel. H C 4.1 4.2 4.
5 ATTACHING THE SECOND FIXED GLASS PANEL 5.1 Use a pencil to mark the screw points in the wall, based on the location of the joints (H). 5.2 Use a size 6 drill bit to drill holes at the marked points. Insert the wall anchors (G) into the holes. 5.3 Attach the joints (H) to the wall with screws (F). 5.4 Attach the joints (H) to the door using screws included with the joints. 3/4” 5.1 5.2 5.3 5.
6 ATTACHING THE BOTTOM HINGES 6.1 Use a pencil to mark the points in each glass pane where the screws for the bottom hinge (N) will be drilled. 6.2 Use a size Ø6 drill bit to drill holes at the marked points to insert the screws. 6.3 Attach the glass-to-glass bottom hinge (N) to the first fixed panel (B), using screws (M) over threshold (O). B 6.1 6.2 Ø6 6.
7 ATTACHING THE SUPPORT ARMS 7.1 Use a pencil to mark the screw points for the support arm (A) on the wall. Use a size 6 drill bit to drill holes at the marked points. 7.2 Insert the wall anchors (G) into the holes in the wall. 7.3 Attach one end of the support arm (A) to the wall, using screws (F). 7.4 Attach the other end of the support arm (A) to the door, using screws (F). Tighten with the Allen key. 7.1 7.2 7.3 G 10 7.
8 ATTACHING THE DOOR 8.1 Affix plastic seal (E) to the hinge side of glass door (D). 8.2 Attach the door (D) to the joints (I) of the fixed glass panel (J). 8.3 Affix plastic seals (C, P) to the length of the glass door (D). 8.4 Affix plastic seals (C, P) to the bottom of the glass door (D). 8.1 I 8.2 8.3 D J 8.
9 ATTACHING THE DOOR HANDLE Attach the shorter door handle (K) vertically to the outer side of the glass door using screws included with the handle. Attach the longer door handle (K) horizontally to the inner side of the glass door, using screws included with the handle.
10 SECURING THE GLASS DOOR Secure the screws on the glass door hinges with the Allen key.
11 COMPLETING THE ASSEMBLY Secure the seals, panels, and door with a caulking gun and high-quality silicone or bathroom grade caulk.
12 DRYING THE DOOR AND PANELS Leave the shower unused for 24 hours, so that it can dry completely.
FINE FIXTURES 206 WEMBLY ROAD - NEW WINDSOR, NY 12553 P: 718.602.6060 F: 718.963.2082 - E: INFO@FINEFIXTURES.COM TOLL FREE: 1.877.8FIXTURES FINEFIXTURES.COM RETAIN THIS INSTALLATION MANUAL FOR FUTURE REFERENCE.
