Nightstand PRODUCT GUIDE & ASSEMBLY INSTRUCTIONS
Should you prefer to speak with a customer service representative, you may call toll free: 1-855-372-2315 2
Guidelines FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY • Do not stand on the item or use as a step ladder • Do not use this item unless all bolts and screws are firmly secured and fastened. • Check all bolts and screws every 90 days. As necessary tighten if any are loose. • Lift up then move. Pushing over or dragging this product can result in an injury or cause damage to the floor and piece.
WARNING: DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF INJURY. Pre-Assembly Preparation: Please read through this instruction booklet before beginning assembly of this item. Two adults are recommended for assembly. • Clear out the space for assembly and lay out all parts on Parts List, extra room will allow you to easily determine if all the pieces are present. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
Parts List 2 1 1 Top Panel (1) 2 Right Panel (1) 5 Back Panel (1) 7 7 Drawer Front (1) 3 6 8 X2 8 Drawer Side Panel (2) Left Panel (1) 6 5 4 4 Bottom Panel (1) 3 Shelf (1) 9 9 Drawer Back Panel (1) 5
Parts List 11 X2 10 10 Drawer Bottom Panel (1) 6 11 Metal Leg (2)
Parts List A Wood Dowel (8) M8x25MM B Cam Lock (10) D15x11MM C Cam Bolt (10) M6x28MM D Cam Hole Cover (10) D:15MM E Small Screw (12) M3.
Parts List J Nail (8) M1.
Step 1 1. Remove all parts from the carton and place them on a protected surface or carpet. 2. Check all parts and hardware against the “Parts List”. 3. Insert 10 Cam Bolts (C) into the Top Panel (1), Bottom Panel (2), Left Side Panel (3) and Right Panel (4). Tighten with a screwdriver or electric screwdriver (not supplied).
Step 2 1. Insert Wood Dowels (A) into the Left Panel (3) and Right Panel (4) as shown below.
Step 3 1. Attach the CL Runner (O) to the Left Side Panel (3) with three M3.5x16MM Screws (E) and tighten with a screwdriver (not supplied). Note: Use the CL mark on the CL Runner (O) to correctly attach the Left Upright Partition (7) as shown below. 2. Attach the CR Runner (O) to the Right Side Panel (4) with three M3.5x16MM Screws (E) and tighten with a screwdriver (not supplied). Note: Use the CR mark on CR Runner (O) to correctly attach the Right upright partition (8) as shown below.
Step 4 1. Attach two Drawer Side Panels (8) to the Drawer Back Panel (9) and Drawer Front Panel (7) with eight M4x38MM Screws (G) and tighten with a screwdriver or electric screwdriver (not supplied) as below image.
Step 5 1. Attach the Drawer Bottom Panel (10) to the assembled unit - unfinished side down side and fasten with eight Nails (J) as shown below.
Step 6 1. Attach the DR and DL Runners (O) to the drawer with six M3.5x16MM Screws (E) and tighten with a screwdriver as shown below.
Step 7 1. Attach a Handle (K) to the Drawer Front (7) with two Bolts (L) and two Washers (M). Tighten with a Screwdriver as shown below.
Step 8 1. Attach the Right Side Panel (4) to the Back Panel (5) and insert one Cam Lock (B) into the Back Panel (5). Tighten with the Allen Key (N). 2. Attach the Left Side Panel (3) to the Back Panel (5) and insert one Cam Lock (B) into the Back Panel (5). Tighten with the Allen Key (N). 4 5 N 3 B B Lock Use a Allen Key to tighten the cam nuts. A quarter turn clockwise is all that is needed.
Step 9 1. Attach the Top Panel (1) to assembled unit – the Left Panel (3), Right Panel (4) and Back Panel (5). 2. Insert six Cam Locks (B) into the Left Panel (3) and Right Panel (4) as shown below. Tighten with the Allen Key (N).
Step 10 1. Attach the Bottom Panel (2) to assembled unit – the Left Panel (3) and Right Panel (4) – with four M6x50MM Screws (I) and tighten with the Allen Key (N).
Step 11 1. Attach a Metal Leg (11) to the Shelf (6) and Left Panel (3) as shown below. 2. Secure the Metal Leg (11) to the Left Panel (3) with four M4x32MM Screws (F) and tighten with a screwdriver. 3. Secure the Metal Leg (11) to the Shelf (6) with two M4x45MM Screws (H) and Tighten with a screwdriver as shown below.
Step 12 1. Attach a Metal Leg (11) to the Shelf (6) and Right Panel (4) as shown below. 2. Secure the Metal Leg (11) to the Right Panel (4) with four M4x32MM Screws (F) and tighten with a screwdriver. 3. Secure the Metal Leg (11) to the Shelf (6) with two M4x45MM Screws (H) and tighten with a screwdriver as shown below.
Step 13 1. Install 10 Cam Hole Covers (D) on all Cam Lock (B) holes.
Step 14 1. Insert the assembled drawer into the assembled unit as shown below.
Periodically (every 90 days) inspect the screws to make sure they are still fully tightened. ATTENTION: Be certain that all screws are fully tightened before using this product.
Product Dimension 7.32 1 19.69inch (50.0cm) 23 m) 4.0c (4 inch 15.7 5inc h (4 0.
Limited Warranty The manufacturers products are warrantied against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as the party or entity which purchases this manufacturer’s furniture from an authorized retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned products.
