User's Manual

12
ProScribe CV
6.1.0 BEFORE YOU BEGIN
The ProScribe is intended for use as Windows XP embedded powered wireless thin client touch-screen device.
 Touse yourProScribeyoumusthavethefollowing;
  •aAC/DCpowersupply(24Vdcoutputvoltage-3,42Adcoutputcurrent)
  •awirelessaccesspointtoaccessthecorporatenetworkor
  •anEthernetconnectionincaseyouplantousetheProScribeonaxedlocation
6.2.0 GETTING STARTED
The Windows XP embedded operating system provides you all the convenience to set-up any type of thin-client session
 withcentrallylocatedapplicationsorweb-basedservices.Beforedoingso,pleasemakesuretoapplythefollowing 
instructions.
IMPORTANT NOTICE :
Write protect
  TheProScribeispre-conguredwithaWindowsXPefeaturecalledEnhancedWriteFilter(EWF)toprevent
writing on the CF card. When write protection is activated, all recently installed software products and changed
user settings are not stored into the CF and hence are removed after a reboot. The procedure to save such data in
  theCFcardisdescribedhereunder.Itisstronglyadvisedtore-enableEWFafterdisablingitforstoringuserdata.
  EWFprotectstheOSbutalsotheCFcarditself.
Procedure to disable EWF
(valid only for software release ≤ 0LBMXNF5107, 0LBMXN1F206)
  •press“start”buttonthen“Run...”andtype“cmd”
  •ontheconsolewindowtype:“ewfmgrc:-commitanddisable-live”
• wait for the command execution
  •nowtheCFiswriteenable,sothemodicationarereallystoredintotheCFcard,meaningthatmodications
will be retained on reboot also if the CF is sets again to read only mode.
  •afterapplyingthedesiredmodications,enabletheEWF(rebootisrequiredforre-enableEWF).
(valid only for software release ≥ 0LBMXNF5108, 0LBMXN1F207)
  •press“start”buttonthen“Run...”andtype“ewfd”
• the ProScribe will logout and reboot automatically
  •nowtheCFiswriteenable,sothemodicationarereallystoredintotheCFcard,meaningthatmodications
will be retained on reboot.
  •afterapplyingthedesiredmodications,enabletheEWF.
Procedure to enable EWF
(valid only for software release ≤ 0LBMXNF5107, 0LBMXN1F206)
•press“start”buttonthen“Run...”andtype“cmd”
  •ontheconsolewindowtype:ewfmgrc:-enable”
• wait for the command execution
  •reboot(itisrequiredforEWFtobereallyenabled)
(valid only for software release ≥ 0LBMXNF5108, 0LBMXN1F207)
  •press“start”buttonthen“Run...”andtype“ewfe”
• the ProScribe will logout and reboot automatically
  •nowtheCFiswritedisable,somodicationarenotstoredintotheCFcard,meaningthatmodicationswill
be lost on reboot.
CAUTION: (valid only for software release ≤ 0LBMXNF5107, 0LBMXN1F206)
  ReboottheProScriberstanddisableEWFbeforeinstallinganynewsoftware.Installingsoftwareand 
  disablingEWFafterwardsisnotsupportedbyWindowsXPeandresultsinsomecasesinasoftwarecrash.
6.2.1 STYLUS RE-CALIBRATION
 Whenthepadispoweredonforthersttime,thepadneedtobecalibrated.
 Seepar.8.1.0forinstructions.