Submittal Sheet

ManualsBrandsField Controls ManualsBoiler VentingVenter/Burner Control System for Oil Systems

120 VAC SYSTEM CONTROL KIT

•

All wiring shall be in accordance with the National Electrical Code and applicable local codes.

DO NOT DESTROY

THESE INSTRUCTIONS MUST REMAIN WITH EQUIPMENT

This device MUST be installed by a qualified agency* in accordance with the manufacturer’s installation instructions.

The definition of a qualified agency is: any individual, firm, corporation or company which either in person or through a

representative is engaged in, and is responsible for, the installation and operation of oil appliances, who is experienced

in such work, familiar with all the precautions required, and has complied with all the requirements of the authority

having jurisdiction.

TEMS INCLUDED IN KIT:

1) Junction box with mounted pressure switch

solid state post purge control

1) 2 Ft. Length of ¼ inch aluminum tubing

1) ¼ inch tubing connector

1) Flexible conduit connector

1) WMO-1 Blocked Vent Switch

WARNING:

Read the installation instructions carefully and completely before proceeding with the installation.

2630 Airport Road, Kinston, NC 28504 • Phone: 252-522-3031 • FAX: 252-522-0214 • www.fieldcontrols.com

Designed for use on SWG Series

Power Vent Hoods for controlling oil

fired heating appliances with 120 VAC

controls.

The CK-63 control has the ability to

operate the oil burner motor (up to 1/3

HP) and the venter at the same time.

This allows for shorter post purge time.

This feature requires the burner to be

equipped with a delayed oil solenoid

valve, which is not supplied with this

kit.

Model: CK-63

Summary of content (12 pages)

PAGE 1
20 VAC SYSTEM CONTROL KIT Designed for use on SWG Series Power Vent Hoods for controlling oil fired heating appliances with 120 VAC controls. Model: CK-63 The CK-63 control has the ability to operate the oil burner motor (up to 1/3 HP) and the venter at the same time. This allows for shorter post purge time. This feature requires the burner to be equipped with a delayed oil solenoid valve, which is not supplied with this kit.
PAGE 2
INSTALLATION MOUNTING JUNCTION BOX The junction box can be mounted at the venter or remotely mounted away from the venter. (See Figure 1 & Figure 2) 1. Remove one of the knockouts from the side of the junction box where the pressure switch is mounted. Install the flexible conduit connector onto the CK-63 Junction Box and secure with fastening nut. If remote mounting the CK-63 Junction Box, mount the flexible conduit connector onto a 2" x 4" installer supplied junction box. 2.
PAGE 3
WIRING INSTRUCTIONS Wire the venter motor and controls in accordance with the National Electrical Code, manufacturer's recommendations and/or applicable local codes. UNIT MUST BE GROUNDED. Check ground circuit to make certain that the unit has been properly grounded. The wiring should be protected by an over current circuit device rated at 15 amperes. Caution must be taken to ensure that the wiring does not come into contact with any heat source.
PAGE 4
Diagram B – Oil Fired System: Page 4 Simultaneous Burner Wiring
PAGE 5
Diagram C – Oil Fired System: Page 5 Wiring With Electronic Primary
PAGE 6
Diagram D – Oil Fire System: Page 6 Simultaneous Burner Wiring With Electronic Primary
PAGE 7
Diagram E – Typical Wiring for Oil Fired Warm Air Furnace with a Honeywell ST9103 Control Board Diagram F – Multiple Oil Fired Systems Page 7
PAGE 8
Diagram G-24V Gas Furnace Application Diagram H-Riello Burner Application Page 8
PAGE 9
ADJUSTMENTS PRESSURE SWITCH ADJUSTMENTS With the venter air flow set and the appliance operating at the best operating efficiency, adjust the pressure switch by rotating the adjustment screw clockwise until the burner shuts off, then rotate the adjustment screw counterclockwise until the burner fires. Rotate the adjustment screw an additional 1/4 to 1/2 turn counterclockwise to ensure proper switch setting.
PAGE 10
TROUBLE SHOOTING HINTS 1. Main burner does not fire when thermostat calls for heat with venter operating. a. Check pressure switch adjustment. (LED should be lit when there is voltage from T1 – T2 and the pressure switch is closed.) b. Check fuel flow. c. Check wiring connections between pressure switch and burner and yellow mode wire connection. d. Check pressure switch for continuity across terminals, during venter operation. 2. Venter does not activate when thermostat calls for heat. a.
PAGE 11
CK-63 Wiring Check-Out Standard Set-up Page 11
PAGE 12
CK-63 Wiring Aquastat Relay Check-Out INSTALLATION INFORMATION CK-63 MODEL NO.: _____________________________________________________ INSTALLER'S NAME: ______________________________________________ INSTALLER'S COMPANY: __________________________________________ INSTALLER'S PHONE NO.