User Guide

ManualsBrandsField Controls ManualsBoiler Venting80+ Gas Draft Induced Furnace Vent Kit

www.eldcontrols.com

Please retain these instructions after installation.

This device MUST be installed by a qualied agency in accordance with the manufacturer's installation instructions. The denition of

a qualied agency is: any individual, rm, corporation or company which either in person or through a representative is engaged

in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the

precautions required, and has complied with all the requirements of the authority having jurisdiction.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By: Phone:

SIDEWALL POWER VENTING KIT

Model: SWG-4G

ITEMS INCLUDED IN KIT:

1 - SWGII-4HD Sidewall Power Venter

1 - CK-43F Control Kit (includes 4" MG-1 Barometric Draft Control)

1 - Installation Instructions

OPTIONAL COMPONENTS:

PEK-4HD Extension Kit. For installations in walls over 8" thick.

GENERAL SYSTEM INFORMATION

Designed for operation with natural gas and LP gas.

1. The thermostat calls for heat and energizes a relay which activates the power venter. After the venter motor

has come up to speed, the pressure switch closes. This closes the circuit to the burner and allows the burner

to re.

2. After the heating requirement has been satised, the thermostat circuit will open and deactivate the burner.

3. The power venter operates for a period of time after the burner has shut o to purge remaining ue gases.

Summary of content (12 pages)

PAGE 1
SIDEWALL POWER VENTING KIT Model: SWG-4G GENERAL SYSTEM INFORMATION Designed for operation with natural gas and LP gas. 1. The thermostat calls for heat and energizes a relay which activates the power venter. After the venter motor has come up to speed, the pressure switch closes. This closes the circuit to the burner and allows the burner to fire. 2. After the heating requirement has been satisfied, the thermostat circuit will open and deactivate the burner. 3.
PAGE 2
WARNING: Bodily injury can result from high voltage electrical components, fast moving fans, and combustible gas. For protection from these inherent hazards during installation and servicing, the electrical supply must be disconnected and the main gas valve must be turned off. If operating checks must be performed with the unit operating, it is the technician’s responsibility to recognize these hazards and proceed safely. INSTALLATION SAFETY INSTRUCTIONS 1.
PAGE 3
INSTALLATION OF THE SWG POWER VENTER 1. Remove power venter from box and inspect unit for damage. If the carton has been crushed or mutilated, check unit very carefully for damage. Rotate blower wheel to insure that the motor and blower wheel rotate freely. DO NOT install if any damage is apparent. 2. Location of the termination of the venting system should be installed in accordance with the National Fuel Gas Code, ANSI Z223.1, CGA Standards B149.1-M91, B149.
PAGE 4
f. The vent termination should not be mounted directly above, or within 3' horizontally from an oil tank vent or gas meter. g. The bottom of the vent terminal shall be located at least 12" above finished grade or maximum expected snow height. 3. After determining the location of the venting system termination point (See Diagram A), cut a square hole through the wall 1" larger than the outer pipe diameter of the power venter. (See Figure 1) 4.
PAGE 5
Table 3 INSTALLATION CLEARANCE WITH SINGLE WALL VENT PIPE DOUBLE PIPE SYSTEM Allowable Inlet Temperature SINGLE PIPE VENTING SYSTEM Clearance (A) Allowable Inlet Temperature ⁄ " Minimum 400ºF Or Less 400ºF To 550ºF 1" Minimum 400ºF To 550ºF 1" Minimum 400ºF To 550ºF ⁄ " Minimum With Sheet Metal Liner 400ºF To 550ºF ⁄ " Minimum With Sheet Metal Liner 400ºF Or Less 12 12 Clearance (A) ⁄ " Minimum 12 12 NOTE: Vent pipe joints should be secured with at least three sheet metal screws.
PAGE 6
INSTALLATION INSTRUCTIONS FOR CK-43F CONTROL KIT Designed for use with the SWG Series Power Venter for controlling Natural Gas and LP Gas Draft Induced appliances. ITEMS INCLUDED IN CK-43F CONTROL KIT: 1- Junction box with mounted air pressure switch and post purge relay/timer 1- 2' Length of 1 ⁄4" aluminum tubing 1- 1 ⁄4" tubing connector 1- Flexible conduit connector 1- 4" MG-1 Barometric Draft Control Figure 7 DRAFT CONTROL INSTALLATION 1.
PAGE 7
WIRING WARNING: Disconnect power supply before installation to prevent personal injury or death from electrical shock and equipment damage. Wire the power venter motor and controls in accordance with the National Electrical Code and applicable local codes. CAUTION: Unit must be grounded. Check ground circuit to make certain that the unit has been properly grounded. CAUTION: All parts of this product that are capable of conducting electrical current are grounded.
PAGE 8
or removing the washer-like weights (supplied with the control) to or from the weight holder chain assembly. After the control is adjusted, its action will be entirely automatic, the gate will open or close by itself to correct for changes in the draft. The control MUST be adjusted to the desired draft setting by adding or removing the washer-type weights supported by the two chains on the side of the draft control.
PAGE 9
PROVING SWITCH ADJUSTMENTS Refer to the following for air pressure switch adjustment procedure and system checkout procedures before operating the appliance continuously. After proper air flow is established, the air pressure switch adjustment is made by turning the adjustment screw clockwise (See Figure 14) until the burner operation stops on the furnace. Slowly turn the adjustment screw counterclockwise until burner ignites.
PAGE 10
4. Determine that the burner is operating properly and that the main burner ignition operates satisfactorily by interrupting and re-establishing the electrical power of the appliance in any convenient manner. Test the pilot or burner safety device to determine if it is operating properly by extinguishing the pilot or disconnecting the flame safety circuit and air pressure switch sensing tube from the pressure switch on the Control Kit. 5. Visually determine that the main burner is burning properly; i.e.
PAGE 11
REPLACEMENT PARTS The following replacement items are available. The Repair Motor Kit contains the Motor and Blower Wheel factory assembled to a mounting bracket.
PAGE 12
Warranty For warranty information about this or any Field Controls product, visit: www.fieldcontrols.com/warranty Phone: 252.522.3031 • Fax: 252.522.0214 www.fieldcontrols.