Specification Sheet

ManualsBrandsfiber mall ManualsComputers & AccessoriesSFP to RJ45 for Palo Alto Networks 1000BASE-T SFP Copper RJ-45 100m Transceiver Module

Table Of Contents

Fiber Optic Module

FIBER MALL CO., LIMITED Rev 1.1 PAGE 1 / 7

SFP-GE-TS

1000Mbps Copper SFP Transceiver, 100m Reach

Product Features



Up to 1.25Gb/s bi-directional data links

 Hot-pluggable SFP footprint

 Extended case temperature range (0°C to +70°C )

 Fully metallic enclosure for low EMI



Low power dissipation (1.05 W typical)



Compact RJ-45 connector assembly

 Access to physical layer IC via 2-wire serial bus

Summary of content (7 pages)

PAGE 1
Fiber Optic Module SFP-GE-TS 1000Mbps Copper SFP Transceiver, 100m Reach Product Features  Up to 1.25Gb/s bi-directional data links  Hot-pluggable SFP footprint  Extended case temperature range (0°C to +70°C )  Fully metallic enclosure for low EMI  Low power dissipation (1.05 W typical)  Compact RJ-45 connector assembly  Access to physical layer IC via 2-wire serial bus FIBER MALL CO., LIMITED Rev 1.
PAGE 2
Fiber Optic Module  1000 BASE-T operation in host systems with SERDES interface Applications  1.25 Gigabit Ethernet over Cat 5 cable Description SFP-GE-TS Copper Small Form Pluggable (SFP) transceivers are high performance, cost effective module compliant with the Gigabit Ethernet and 1000- BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supp-Orting 1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cables.
PAGE 3
Fiber Optic Module Low-Speed Signals MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. Electronic Characteristics Parameter Symbol Min Max Units Notes/Conditions GBIC Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector GBIC Output HIGH VOH host_Vcc - 0.5 host_Vcc + 0.3 V 4.
PAGE 4
Fiber Optic Module High-speed electrical interface (Host-GBIC) Parameter Symbol Min Single ended data input swing Vinsing Single ended data output swing Voutsing Rise/Fall Time Tr,Tf Tx Input Impedance Rx Output Impedance Typical Max Units Notes/Conditions 250 1200 mV Single ended 350 800 mV Single ended 175 psec 20%-80% Zin 50 Ohm Single ended Zout 50 Ohm Single ended General Specifications Parameter Symbol Min Data Rate BR 10 Cable Length L Typical Max Units Not
PAGE 5
Fiber Optic Module Pin Descriptions Pin Signal Name Description Plug Seq. 1 VEET Transmitter Ground 1 2 TX FAULT Transmitter Fault Indication 3 Note 1 3 TX DISABLE Transmitter Disable 3 Note 2 4 SDA SDA Serial Data Signal 3 5 SCL SCL Serial Clock Signal 3 6 MOD_ABS Module Absent. Grounded within the module 3 7 RS0 Not Connected 3 8 LOS Loss of Signal 3 9 VEER Receiver ground 1 10 VEER Receiver ground 1 11 VEER Receiver ground 1 12 RD- Inv.
PAGE 6
Fiber Optic Module 16 VCCT Transmitter Power Supply 2 17 VEET Transmitter Ground 1 18 TD+ Transmit Data In 3 Note 5 19 TD- Inv. Transmit Data In 3 Note 5 20 VEET Transmitter Ground 1 Notes: Plug Seq.: Pin engagement sequence during hot plugging. 1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind.
PAGE 7
Fiber Optic Module Ordering Information Part Number Product Description SFP-GE-TS 1000Mbps only,RJ45 interface, Copper SFP FIBER MALL CO., LIMITED Rev 1.