User Manual

ManualsBrandsFibar Group ManualsElectronicsFibaro KeyFob

BATTERY

#9: Battery

Checking battery level:

KeyFob automatically warns about low battery with 3 yellow blinks,

when battery level is below value selected in parameter 3.

1. Press

and simultaneously.

2. Press

or until LED glows cyan.

3. Press

4. LED indicates battery level with a smoothly transitioning colours,

where:

• Green - 100%

• Yellow - 50%

• Red - 1%

5. Wait 2 second or press any button to exit.

Replacing the battery:

KeyFob can be powered with CR2450 (included) battery. Estimated

battery life with device added once, default settings, direct range and

maximum 5 pushes per day is 2 years.

1. Using a coin, open the battery cover by turning it counter-clock-

wise.

2. Replace the battery.

3. Using a coin, close the battery cover by turning it clockwise.

2. 3.

CAUTION

Using batteries other

than specied may

result in explosion.

Dispose of properly,

observing environ-

mental protection

rules.

NOTE

Battery life depends

on frequency of us-

age, number of associ-

ations/scenes, Z-Wave

routing and network

load.

Summary of content (10 pages)

PAGE 1
2 #9: Battery ! CAUTION Using batteries other than specified may result in explosion. Dispose of properly, observing environmental protection rules. i NOTE Battery life depends on frequency of usage, number of associations/scenes, Z-Wave routing and network load. KeyFob can be powered with CR2450 (included) battery. Estimated battery life with device added once, default settings, direct range and maximum 5 pushes per day is 2 years.
PAGE 2
13 #10: Associations Association (linking devices) - direct control of other devices within the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter or scene (may be controlled only through a Z-Wave controller). The device provides the association of thirteen groups: 1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).
PAGE 3
14 The KeyFob in 2nd to 13th group allows to control 5 regular or multichannel devices per an association group. “LifeLine” group is reserved solely for the controller and hence only 1 node can be assigned. It is not recommended to associate more than 10 devices in general, as the response time to control commands depends on the number of associated devices. In extreme cases, system response may be delayed. To add an association (using the Home Center controller): 1.
PAGE 4
15 #11: Advanced parameters The KeyFob allows to customize its operation to user’s needs. The settings are available in the FIBARO interface as simple options that may be chosen by selecting the appropriate box. In order to configure the KeyFob (using the Home Center controller): 1. Go to the device options by clicking the icon: 2. Select the „Advanced” tab. 3. Modify values of chosen parameters.
PAGE 5
16 4. Second scene sequence This parameter allows to set up sequence that activates scene with ID 8. See "Sequences" on page 10 for more information. Available settings: 0 - 1st sequence disabled Default setting: 9-28086 - value of sequence 0 Parameter size: 2 [bytes] 5. Third scene sequence This parameter allows to set up sequence that activates scene with ID 9. See "Sequences" on page 10 for more information.
PAGE 6
17 10. Single button associations - operating mode This parameter allows to choose operating mode for single button associations. Available settings: 0 - single press switches state to opposite 1 - single press switches state to opposite, double press sets to maximum level Default setting: 2 - single press turns on, double press turns off Parameter size: 1 [byte] 0 (switch) 11. Value sent to association group 12. Value sent to association group 13. Value sent to association group 14.
PAGE 7
18 19. Paired buttons association for and This parameter allows to activate paired buttons association mode for and buttons. Paired buttons are dependent and association are sent only to groups. turns devices on and increases value, turns them off and decreases value. Available settings: 0 - paired buttons association inactive Default setting: i NOTE Parameters 21 to 26 values may be combined, e.g. 1+2=3 means that pressing button once or twice will result in sending assigned scene ID.
PAGE 8
19 #12: Specifications Power supply: CR2450 3.0V battery (included) Battery life: est. 2 years (default settings, max. 5 pushes per day and direct range) Operating temperature: 10 - 40°C EU directives compliance: RoHS 2011/65/EU R&TTE 1999/5/EC Radio protocol: Z-Wave (500 series chip) Radio frequency: 868.4 or 869.8 MHz EU; 908.4, 908.42 or 916.0 MHz US; 921.4 or 919.8 MHz ANZ; 869.
PAGE 9
20 #13: Regulations This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 10
21 Note Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules. DGT Warning Statement Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.