O P E R AT I N G MANUAL EN FIBARO MOTION SENSOR FGBHMS-001 CONTENTS #1: Description and features #2: Powering the accessory #3: Pairing the accessory #4: Physical installation #5: Reset v1.
Important safety information ! Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of operating manual.
#1: Description and features FIBARO Motion Sensor is a HomeKit-enabled multi-sensor using Bluetooth® low energy technology. Along with detecting motion, the accessory measures the ambient temperature and light intensity. The sensor has a built-in accelerometer to detect any tampering with the accessory. FIBARO Motion Sensor is battery powered and designed to be installed quickly and easily on any surface.
#2: Powering the accessory 1. Turn the cover counter-clockwise and open it. i NOTE Remember to use only battery type specified in the manual and keep the right polarity. i 2. Remove the battery blocker and check if the battery is placed correctly. NOTE If the accessory blinks green after powering, it is already paired and has to be reset to pair again. 3. The accessory will glow red – it is ready to be paired. 4. Close the cover and turn it clockwise, dots on the casing should align.
#3: Pairing the accessory 1. Open the Settings app on your iOS device. 2. Go to the Bluetooth® section, and turn the Bluetooth® on. 3. Place the accessory next to your iOS device. 4. Open a HomeKit app of your choosing on your iOS device. 5. Open pairing window in your HomeKit app to detect available accessories. i NOTE Use Fibaro app to fully utilize this product. Other HomeKit compatible apps might not support all of its features. 6. Choose Motion Sensor you wish to pair. 7.
#4: Physical installation Installing the Motion Sensor: 1. Install the holder (using an expansion bolt or a sticker). Sticker 2. Insert the device into the holder. 3. Test the operation - check whether the device indicates motion detection. Detection range: Detection range of the Motion Sensor is shown below. Actual range of the Sensor can be influenced by environmental conditions.
#5: Reset Resetting the Motion Sensor to factory defaults: Reset procedure allows to restore the accessory back to its factory settings including HomeKit pairing. We recommend performing resetting procedure within range of your iOS device’s Bluetooth®. 1. Open the cover. 2. Press and hold the button. Button i NOTE If reset procedure was performed outside iOS device’s Bluetooth® range the accessory will not be removed from the HomeKit app and will not respond.
#6: Functionalities i NOTE If you are using Fibaro app you can adjust sensitivity, sustain time and LED indication for motion detection using parameters. i NOTE If you are using Fibaro app you can adjust sensitivity and indications for tamper detection using parameters. i NOTE The accessory measures temperature in the place of installation. Remember that temperature near the ceiling may differ from that on eye-level or the floor.
#7: Configurable parameters 1. Motion detection – sensor sensitivity This parameter allows to set sensitivity of PIR sensor used for motion detection. The higher the value of this parameter, the higher the sensitivity. Available settings: 1 – low sensitivity 2 – medium sensitivity Default setting: 3 – high sensitivity 2 (medium sensitivity) 2. Tamper – sensor sensitivity This parameter allows to set sensitivity of tamper detection. The higher the value of this parameter, the higher the sensitivity.
5. Motion detection - sustain time This parameter allows to set how long the information about detected motion is sustained by the accessory. Each subsequent motion detection causes time to be counted from the beginning.
#8: Specifications Power supply: 3.0V DC battery Battery type: CR123A EU directives compliance: R&TTE 1999/5/EC RoHS 2011/65/EU Radio protocol: Bluetooth® low energy Radio frequency: 2.4 GHz Range: up to 50m (free range) (164 feet) Recommended installation height: 2.4 meters (7.87 feet) Operating temperature: 0-40°C (32-104°F) Temperature measuring range: 0-40°C (32-104°F) Temperature measuring accuracy: ±0.5°C (±0.
#9: Regulations This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DGT Warning Statement Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.
