O P E R AT I N G MANUAL EN FIBARO DOOR/WINDOW SENSOR FGBHDW-002 CONTENTS #1: Description and features #2: Powering the accessory #3: Pairing the accessory #4: Physical installation #5: Reset v1.
Important safety information ! Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of operating manual.
#1: Description and features FIBARO Door/Window Sensor is a HomeKit-enabled Hall effect sensor using Bluetooth® low energy technology. Along with detecting opening/closing, the accessory measures the ambient temperature. Opening is detected by separating the sensor’s body and the magnet. Tampering is detected whenever the accessory is detached from the surface or casing is opened.
#2: Powering the accessory 1. Open the cover. 2. Remove the battery blocker. i NOTE If after powering accessory blinks three times, it is already paired and has to be reset to pair again. 3. The accessory will glow blue for 1.5 seconds – it is ready to be paired. 4. Close the cover.
#3: Pairing the accessory 1. Open the Settings app on your iOS device. 2. Go to the Bluetooth® section, and turn the Bluetooth® on. 3. Place the accessory next to your iOS device. 4. Open a HomeKit app of your choosing on your iOS device. 5. Open pairing window in your HomeKit app to detect available accessories. i NOTE Use Fibaro app to fully utilize this product. Other HomeKit compatible apps might not support all of its features. 6. Choose Door/Window Sensor you wish to pair. 7.
#4: Physical installation To install the Door/Window Sensor: 1. Stick the included self-adhesive pads to the bottom of the device and magnet. 2. Peel off the protective layer of the sticker. 3. Stick the device onto the door/window frame. 4. Stick the magnet onto the moving part of the door/window, no further than 5mm from the sensor. Positioning of the Sensor and the magnet: Correct postioning of the magnet in relation to the Sensor: max.
#5: Reset Resetting the Door/Window Sensor to factory defaults: Reset procedure allows to restore the accessory back to its factory settings including HomeKit pairing. We recommend performing resetting procedure within range of your iOS device’s Bluetooth®. 1. Open the cover. 2. Press the button 3 times then press and hold the button. Button i NOTE If reset procedure was performed outside iOS device’s Bluetooth® range the accessory will not be removed from the HomeKit app and will not respond.
#6: Functionalities i NOTE If you are using Fibaro app you can change the default state of sensor and its indications using parameters. Opening/closing detection: The Door/Window Sensor detects opening/closing using Hall effect sensor and reports it to your iOS device. Opening is detected by separating the sensor’s body and the magnet. Changing the state is indicated with one blink.
#7: Configurable parameters 1. Opening/closing detection – LED indication This parameter allows choose if opening/closing is indicated by the built-in LED diode. Available settings: 0 – indications disabled Default setting: 1 – indications enabled 1 (indications enabled) 2. Door/window state This parameter allows to set in what state is door/window when the magnet is close to the sensor.
#8: Specifications ! CAUTION Using batteries other than specified may result in explosion. Dispose of properly, observing environmental protection rules. Specifications Power supply: 3.6V DC battery Battery type: ER14250 ½ AA EU directives compliance: R&TTE 1999/5/EC RoHS 2011/65/EU Radio protocol: Bluetooth® low energy Radio frequency: 2.
#9: Regulations This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DGT Warning Statement Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.
