User Manual

D. Index
D−23
Festo P.BE−SPC200−EN en 0901d
S
Safety instructions XI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save the configuration 4−25 . . . . . . . . . . . .
. . . . . . . . . . . . . . .
Saving the hardware configuration 4−24 . . . . . . . . . . . . . . . . .
Screw connectors 3−10 . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
Sequence plans for the programmer C−3 . . . . . . . . . . . . . . . .
Carry out fault acknowledgement C−10 . . .
. . . . . . . . . . . . .
Create readiness to operate C−3 . . . . . . . . . . . . . . . . . . . . .
Start NC record in Record Select mode C−7 . . .
. . . . . . . . . .
Start program or NC record C−9 . . . . . . . . . . . . . . . . . . . . . .
Switch−on behaviour 5−5 . . . . . . . . . .
. . . . . . . . . . . . . . . . .
Serial interfaces (X4) 3−36 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service
XII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service unit (compressed air supply) 3−6 . . .
. . . . . . . . . . . . .
Set acceleration ramp (NC command G08/G09)
Approach ramp (pneumatic axis) 7−41 . . . . . . . . . . . . . . . .
Braking ramp (pneumatic axis) 7−43 . . . . . .
. . . . . . . . . . . .
Stepping motor axis 7−42 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set mass assessment (NC command M37) 7−76
. . . . . . . . . .
Set nominal value mode (NC command M13) 7−73 . . . . . . . .
Set single−bit operand (NC command #S) 7−85 . . . . . . . . . . .
Set speed limit value (NC command M41)
7−81 . . . . . . . . . . .
Set stroke limit value (NC command M40) 7−80 . . . . . . . . . . .
Short circuit, Sensor supply 8−8 . . . . . . . . . . . . . .
. . . . . . . . .
Short−circuit diagnosis C−18 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal filter factor
Definition B−9 . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definition (controller data) 4−22 . . . . . . . . . . . . . . . . . .
. . . .
Examples B−13 , B−14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting on the control panel 6−51 . . . . . .
. . . . . . . . . . . . . .
Signals, explanation of all I/O signals
In Record Select mode 5−22 . . . . . . . . . . . . . . . . . . . . . . . . .
In
Start/Stop mode 5−11 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slide mode A−8 . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .