User Manual

D. Index
D−22
Festo P.BE−SPC200−EN en 0901d
REF (axis status flag reference set) 7−22 . . . . . . . . . . . . . . . . .
Reference configuration 4−6 . . . . . . . . . . . . . . . . . . . . . . . .
. .
Saving with the control panel 6−24 . . . . . . . . . . . . . . . . . . .
Reference point (DNCI) 3−23 . . . . . . . . . . . . . . . . . . .
. . . . . . .
Reference position (stepping motor) 4−21 . . . . . . . . . . . . . . .
Setting with the control panel 6−23 . . . . . . . . . . . . . . . . . .
.
Reference speed (pneumatic axis) 4−19 . . . . . . . . . . . . . . . . .
Reference speed factor (stepping motor) 4−21 . . . . . . . . . . . .
Setting with the control panel 6−23 . . .
. . . . . . . . . . . . . . . .
Reference stop (DNCI) 3−22 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference travel
Setting with
the control panel (stepping motor axis) 6−54 .
Start (NC command G74) 7−59 , 7−62 . . . . . . . . . . . . . . . . . .
Reference travel mode
Entry with NC command 7−59 , 7−62 . . . . . . . .
. . . . . . . . . . .
Setting with the control panel (stepping motor) 6−23 . . . .
Reference voltage 3−47 , C−28 . . . . . . . . . . . . . . . . . . . . . . .
. .
Referencing speed (pneumatic axis) 7−61 . . . . . . . . . . . . . . . .
Register Rn 7−19 . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .
Add to register (NC command #AR) 7−89 . . . . . . . . . . . . . .
Load (NC command #L) 7−89 . . . . . . . . . . . . .
. . . . . . . . . . .
Over view 7−14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test
(NC command #TR) 7−90 . . . . . . . . . . . . . . . . . . . . . . . .
Testing with the control panel 6−53 . . . . . . . . . . . . . . . . .
. .
Relative dimension specification
with positioning commands (NC command G91) 7−65 . . . .
RESET, With the control panel 6−47 . . . . . . . . . . . . . . . . . . . . .
RESET (program error) 5−12 . . .
. . . . . . . . . . . . . . . . . . . . . . .
RESET signal (Record Select mode) 5−23 . . . . . . . . . . . . . . . .
Pin assignment 3−43 . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset single−bit operand (NC command #R) 7−85 . . . . . . . . .
Reset system, With the control panel
6−47 . . . . . . . . . . . . . . .
Resolution (stepping motor) 4−21 . . . . . . . . . . . . . . . . . . . . . .
Setting with the control panel 6−23 . . .
. . . . . . . . . . . . . . . .
Rotary drive A−24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .