User's Manual

ManualsBrandsFERMAX ManualsSecurity EquipmentRESISTANT KEYPAD AND PROXIMITY READER

INTRODUCTION

The SK5-X/SK6-X is a universal keypad, can work as standalone keypad,

access controller or standard Wiegand output reader. It uses Atmel

MCU assuring stable performance. The operation is very user-friendly,

and low-power circuit makes it long service life.

The SK5-X/SK6-X supports 600 users, it support multi access modes

in either card access, PIN access, Card+PIN access, or multi cards/PINs

access, it can read 125KHz EM & HID for Low Frequency and 13,56MHz

Mifare for High Frequency tokens,cards and tags. Another advantage

of the SK5-X/SK6-X is it has extra features including block enrollment,

interlock, Wiegand 26~37 bits interface, 12~28V AC/DC voltage…etc.

Carton Inventory

Screw Driver

Master Cards

Master Add Card

Master Delete Card

Diode 1N4004 (For

relay circuit protection)

Self Tapping Screws

Wall Anchors

SK5-X/SK6-X

User Manual

Features

Waterproof, conforms to IP66

One relay, keyboard programmer

600 users

PIN length: 4~6 digits

Card type: 125KHz EM card, 125KHz HID card, 13.56MHz Mifare card

Wiegand 26~37 bits input & output

Can be used as Wiegand reader with LED & Buzzer output

Card block enrolment

Tri-colour LED status display

Pulse mode, Toggle mode

2 devices can be interlocked for 2 doors

Built in light dependent resistor (LDR) for anti tamper

Backlit keypad

Low temperature resistance(-40℃)

Wiring Connections

Environment

Operating Temperature

Operating Humidity

Relay output, exit button, alarm,

door contact, Wiegand input,

Wiegand output

Meets IP66

-40℃~60℃ (-40℉~140℉)

10%RH~ 98%RH

Physical

Zinc-Alloy Enclosure

Surface Finish

Dimensions

Unit Weight

Shipping Weight

Powder Coat

L150×W51×H23mm(SK6-X)

500g

650g

Wiegand Interface

Wiegand Input

Wiegand Ouput

User Capacity

Common Users

Panic Users

598

Operating Voltage

Idle Current

Active Current

12~28V AC/DC

< 65MA

< 100MA

Proximity Card Reader

Radio Technology

Read Range

HID & EM & Mifare

125KHz & 13.56MHz

2~6cm

PIN Output

Relay

Adjustable Relay Output Time

Lock Output Load

One (NO, NC, Common)

0~99 Seconds (5 seconds default)

2 Amp Maximum

INSTALLATION

Remove the back cover from the unit

Drill 2 holes(A,C) on the wall for the screws and one hole for the cable

Knock the supplied rubber bungs to the screw holes(A,C)

Fix the back cover ﬁrmly on the wall with 4 ﬂat head screws

Thread the cable through the cable hole(B)

Attach the unit to the back cover

Green

White

D 0

D 1

Grey

Brown

Wiegand Input/Output Data 0

Wiegand Input/Output Data 1

Negative contact for Alarm

Door/Gate Contact Input

(Normally Closed)

Alarm Output

Contact Input

Set Working Mode

1. Enter Program Mode

3. Exit Program Mode

(Master Code) #

8 1 #

8 0 # (Factory default)

Notes: the SK5-X/SK6-X has 3 working modes: Standalone Mode,

Controller Mode, Wiegand Reader Mode, choose the mode you use.

(Factory default is Standalone Mode / Controller Mode)

STANDALONE MODE

SK5-X/SK6-X can be worked as Standalone Reader for single door.

(Factory default mode)---8 0 #

Connection Diagram

Common Power Supply:

Access Control Power Supply:

Programming

Programming will vary depending on access conﬁguration.

Follow the instructions according to your access conﬁguration.

Set Relay Conﬁguration

Programming Step Keystroke Combination

1. Enter Program Mode (Master Code) #

2. Pulse Mode 3 (1-99) # (factory default)

The relay time is 1-99 seconds.

(1 is 50mS) (Default is 5 seconds)

Sets the relay to ON/OFF Toggle mode

2. Toggle Mode

3. Exit

3 0 #

The relay conﬁguration sets the behaviour of the output relay on activation.

Set Access Mode

For Multi cards/ PINs access mode, the interval time of reading

cards/inputting PINs can not exceed 5 seconds, or else, the SK5-X/SK6-X

will exit to standby automatically.

1. Enter Program Mode

2. Card access

2. Card or PIN access

3. Exit

2. Card+PIN access

(Master Code) #

4 0 #

4 1 #

4 2 # (Factory default)

4 3 (2~9) #

2. Multi cards/PINs access

(Only after reading 2~9 cards or PINs,

the door can be opened)

Door Detecting

Door Open Too Long (DOTL) warning: When used with an optional

magnetic contact or built-in magnetic contact of the lock, if the door

is opened normally, but not closed after 1 minute, the inside buzzer

will beep automatically to remind people to close the door and

continue for 1 minute before switching off automatically.

Door Forced Open warning: When used with an optional magnetic

contact or built-in magnetic contact of the lock, if the door is opened

by force, or if the door is opened after 60 seconds of the electro

-mechanical lock not closed properly, the inside buzzer and alarm

output will both operate. Enter Master code # or valid user

card /PIN to silence.

Users Operation & Reset to Factory Default

CONTROLLER MODE

SK5-X/SK6-X can work as Controller, connected with the external Wiegand

reader. (Factory default mode)---8 0#

Connection Diagram

- Open the door: Read valid user card or inputting valid user PIN

- Remove Alarm: Read valid user card or inputting valid user PIN,

or input Master Code #

- To reset to factory default & Add Master Cards: power off, press

the exit button, hold it and power on, there will be two beeps, and the

LED light turns into yellow, release the exit button, then read any two

cards(can be 125KHz EM card, 125KHz HID card or 13.56MHz Mifare

card, the LED will turn into red, means reset to factory default

successfully. Of the two cards reading, the 1 one is Master Add

Card, the 2 one is the Master Delete Card.

Remarks:

① If no Master Cards added, must press the Exit Button for at least

10 seconds before release.

② Reset to factory default, the user's information is still retained.

Attention: Install a 1N4004 or equivalent diode is needed when use

a common power supply, or the reader might be damaged.

(1N4004 is included in the packing)

Set Master Code

1. Enter Program Mode

3. Exit Program Mode

(Master Code) #

0 (New Master Code) # (Repeat New Master Code)

2. Update Master Code

(Master code is any 6 digits)

ADVANCED APPLICATION

Interlock

Connection Diagram:

Remarks: The Door Contact must be installed and connected as

the diagram.

Let's name the two SK5-X/SK6-X Keypads as “A”and “B” for two

doors “1” and “2”

Step1:

Enroll the users on Keypad A and Keypad B

Step2:

Set both of the two readers (A and B) to Interlock function

1. Enter Program Mode

2. Interlocked-OFF

(Master Code) #

9 0 # (factory default)

2. Interlocked-ON

3. Exit

9 1 #

The interlock operation is ﬁnished,

When and only door 2 is closed, the user can read the valid card or

input PIN on Reader A, door 1 will open; then when and only door

1 closed, read valid card or input PIN on Reader B, door 2 will open.

SK5-X/SK6-X

Attention:

Install a 1N4004 or equivalent diode is needed when use

a common power supply, or the keypad might be damaged.

(1N4004 is included in the packing)

Programming Step Keystroke Combination

1. Enter Program Mode (Master Code) #

Set Strike-out Alarm

The strike-out alarm will engage after 10 failed card/PIN attempts

(Factory default is OFF). It can be set to deny access for 10

minutes after engaging or disengage only after entering a

valid card/PIN or Master code.

1. Enter Program Mode

2. Strike-Out OFF

2. Strike-Out ON (Alarm)

3. Exit

2. Strike-Out ON

(Master Code) #

6 0 # (factory default)

6 1 # Access will be denied for 10 minutes

6 2 #

Set Audible and Visual Response

1. Enter Program Mode

2. Control Sounds

2. Control Keypad Backlit

3. Exit

2. Control LED

(Master Code) #

OFF = 7 0 #

OFF = 7 2 #

OFF = 7 4 #

ON = 7 1 #

ON = 7 3 #

ON = 7 5 #

(factory defaults are ON)

Master Cards Usage

Using Master Cards to add and delete card / PIN users

Add a User

1. (Read Master Add Card)

2. (Read User Card)

Repeat Step 2 for additional user cards

3. (Read Master Add Card)

Delete a User

1. (Read Master Delete Card)

2. (Read User Card)

Repeat Step 2 for additional user cards

3. (Read Master Delete Card)

2. To disable door open detection 5 0 # (factory default)

5 1 #

3. Exit

2. To enable door open detection

WIEGAND READER MODE

SK5-X/SK6-X can work as Standard Wiegand Reader, connected to

the third party Controller--- 8 1 #

Connection Diagram

Keypad Reader

Set Wiegand Output Formats

Please set the Wiegand output formats according to the Wiegand

input format of the controller.

Note:

-Yellow wire: Buzeer control

If you need to connect Brown/Yellow wires:

When the input voltage for LED is low, the LED will turn into

Green; and when the input voltage for Buzzer is low, it will sound.

-Brown wire: Green LED light control

When set into Wiegand Reader mode, nearly all settings in

Controller Model will become invalid. And Brown & Yellow

wires will be redeﬁned

as below:

1. Enter Program Mode

2. Wiegand output bits

3. Exit

(Master Code) #

8 (26~37) # (factory default is 26bits)

8 (4 or 8 or 10) # (Factory default is 4bits)

PIN output bits

Add PIN Users:

To add PIN users, after enter into programming mode on SK5-X/SK6-X,

PIN(s) can be input/ added on either SK5-X/SK6-X controller or the external

Keypad Reader.

Delete PIN Users:

the same way as add users.

CONTENTS

WIEGAND

READER MODE

STANDALONE

MODE

ADVANCED

APPLICATION

CONTROLLER

MODE

INTRODUCTION

INSTALLATION

Operation Status LED Buzzer

Enter into programming mode

In the programming mode

Operation error

Exit from the programming mode

Open lock

Red light shines

Orange light bright

Red light bright

Green light bright

Alarm

Red light Shines quickly

Stand by Red light bright

One beep

Three beeps

One beep

Beeps

Basic Conﬁgure

Enter Program Mode

Exit Program Mode

(Master Code) #

(Factory default is 123456)

Sound and Light Indication

Door Bell Connect (for SK6-X only)

Door

Bell

Brown & Black

Yellow & Black

Power +

Power

Door Bell B

Door Bell A

Power

Programming

- Basic Programming is the same as Standalone Mode

- There are some exceptions for your attention:

SK5-X/SK6-X Connected with External Card Reader:

If EM card reader or HID card reader: users can be added/deleted

on either SK5-X/SK6-X or external reader.

If Mifare reader: users can only be added/deleted on external reader.

SK5-X/SK6-X Connected with Fingerprint Reader:

For example:

Connect F2 as the ﬁngerprint reader to SK5-X/SK6-X, it is of two

steps to enroll the valid ﬁngerprint.

Step 1: Add the Fingerprint (A) on F2

Step 2: Add the same Fingerprint(A) on SK5-X/SK6-X:

Enter Program Mode:

(Master Code) #

1 (Press Fingerprint A once on F2) # (ID auto allocated)

1 (User ID) # (Press Fingerprint A on F2) # (Select speciﬁc ID)

Exit:

Remarks: 4 means 4 bits, 8 means 8 bits, 10 means 10 digits virtual

number.

1. Enter Program Mode

2.PIN input bits

3. Exit

(Master Code) #

8 (4 or 8 or 10) #

(factory default is 4bits)

SK5-X/SK6-X Connected with Keypad Reader:

The keypad reader can be 4 Bits, 8 Bits (ASCII), or 10 Bits output

format. Choose the below operation according to the PIN output

format of your reader.

Set Wiegand Input Formats

Please set the Wiegand input formats according to the Wiegand

output format of the external Reader.

1. Enter Program Mode

3. Exit

(Master Code) #

2. Wiegand input bits

8 (26~37) # (factory default is 26bits)

Speciﬁcations

Brown & Black

(SK6-X)

Yellow & Black

(SK6-X)

Contact for Door Bell

Door Bell A

Door Bell B

600

Yellow

OPEN

Request to Exit(REX) Input

White & Black

Relay Common

Common Connection for Relay

Output

Green & Black

Relay NC

Normally Closed Relay Output

Wiring

Wire Color

Function Notes

Red

AC&DC

12-28V AC/DC Power Input

Blue

Relay NO

Normally Open Relay Output

Black

GND

Negative Pole

Advanced Input and Output Features

Pass-Through Wiring (Wiegand Reader or Controller)

Keystroke CombinationProgramming Step

2. Standalone/Controller Mode

2. Wiegand Reader Mode

Keystroke Combination

Programming Step

Notes:

User ID number: Assign a user ID to the access card / PIN in order to

track it. The common user ID number can be any number from 1~598, the

panic user ID is from 599~600. IMPORTANT: User ID is do not have to be

proceeded with any leading zeros. Recording of User ID is critical.

Modiﬁcations to the user require the User ID be available.

Proximity Card: Any 125KHz industry standard 26 bits HID and

EM cards and 13.56MHz Mifare card.

PIN: Can be any 4~6 digits except 8888 which is reserved.

Add Panic Users

Add Common Users

1. Enter Program Mode

(Master Code) #

Add Card User

2. Add Card: Using Auto ID 1 (Read Card) #

(Allows SK5-X/SK6-X to assign Card

to next

available User ID number)

The cards can be added continuously.

1 (User ID) # (Read Card) #

(User ID is any number from 1-598)

2. Add Card: Select Speciﬁc ID

(Allows Master to deﬁne a speciﬁc

User ID to associate the card to)

2. Add Card: by Card Number

2. Add Card: Block Enrolment

(Allows Master to add up to 598 card

to the Reader in a single step)

Takes 2 minutes to program.

1 (Input 8/10 digits Card number) #

1 (User ID) # (Card quantity) # (The

ﬁrst card number) #

Add PIN User

1 (PIN) #

The PINs can be added continuously.

2. Add PIN: Using Auto ID

(Allows SK5-X/SK6-X to assign PIN

to next

available User ID number)

1 (User ID) # (PIN) #

The user ID is any number from 1-598

2. Add PIN: Select Speciﬁc ID

(Allows Manager to deﬁne a speciﬁc

User ID to associate the PIN to)

(PIN: 4~6 digits)

3. Exit

Cards’ number must be consecutive;

Card quantity=number of cards to be

enrolled.

Keystroke CombinationProgramming Step

1. Enter Program Mode (Master Code) #

2. Add Card: 1 (User ID) # (Read Card / Input 8/10

digits Card number) #

(User ID is any number from 599~600)

2. Add PIN:

3. Exit

1 (User ID) # (PIN) #

Change PIN Users

Note: Below is done outside programming mode, users can undertake

this themselves

1. Change PIN: By Card (Read Card) (Old PIN) # (New PIN) #

PIN(8888) to cards when adding)

(Repeat New PIN) #

2. Change PIN: By PIN

3. Exit

(There will auto allocate

(User ID) # (Old PIN) # (New PIN) #

Delete Users

1. Enter Program Mode (Master Code) #

Delete Common Card User

2. Delete Card - By Card 2 (Read Card) #

2. Delete Card - By ID number

The cards can be deleted continuously.

2 (Input 8/10 digits Card number) #

2.Delete User - By Card number

2 (User ID) #

Delete Common PIN User

2.Delete PIN - By PIN 2 (Input PIN) #

2.Delete PIN - By ID number

2 (User ID) #

Delete Panic User

Delete All Users

2.Delete Panic Card User 2 (User ID) #

2.Delete Panic PIN User

2 (User ID) #

3. Exit

2. Delete All Users

2 (Master Code) #

Keystroke CombinationProgramming Step

Programming Step Keystroke Combination

Keystroke CombinationProgramming Step

Basic Standalone Wiring

70mm

53mm

123mm

Grey & Black

AC&DC

12-28V AC/DC Power Input

ALARM-

OPEN

D_IN

GND

AC&DC

COM

Green

White

Grey

Yellow

Brown

Red

Grey & Black

Blue

White & Black

Green & Black

Black

DC /3A12V

Door

detecting switch

Special Power Supply

Alarm

NC COM NO

+12V

GND

V+

GND

OPEN

Exit button

Wiegand reader

Fail-Safe lock

Fail-Secure lock

SK5-X/SK6-X

Green & Black

AC&DC

Grey & Black

White & Black

AC&DC

Green & Black

Grey & Black

White & Black

Power

Exit Button

Fail-Safe Lock: NC

Fail-Secure Lock: NO

Power "+"

1n4004

Lock

Door

detecting switch

Power "+"

Alarm "-"

Alarm

12-28V AC/DC

ALARM-

OPEN

D_IN

GND

AC&DC

COM

Green

White

Grey

Yellow

Brown

Red

Grey & Black

Blue

White & Black

Green & Black

Black

SK5-X/SK6-X

Exit Button

Door

detecting switch

SK5-X/SK6-X

Alarm "-"

Alarm

Power

GND

NOCOM

+12V

DC 12V/3A

Fail-Secure lock

Fail-Safe lock

PUSH

ALARM-

OPEN

D_IN

GND

AC&DC

COM

Green

White

Grey

Yellow

Brown

Red

Grey & Black

Blue

White & Black

Green & Black

Black

SK5-X/SK6-X Simpliﬁed Instruction

Operation

0 - New Code - # - Repeat the New Code - #

(code: 6 digits)

1 - Read Card - #

(can add Card continuously)

1 - PIN - #

2 - Read Card - # for Card user

2 - PIN - # for PIN user

Exit From the Programming

Mode

Function Description

Enter the Programming Mode

Change the Master Code

Add Card User

Add PIN User

Delete User

How to be granted access

Card User

PIN User

Read card

Input PIN #

- 123456 - #

then you can do the programming

(123456 is the factory default master code)

(PIN Length: 4~6 digits)

1 2

5 6

Access Controller/Reader

SK5-X

SK6-X

L148xW56xH22.5mm(SK5-X)

1 2

5 6

The SK5-X/SK6-X supports the Interlock funciton. It is of two keypads

for two doors, and mainly used for banks, prisons, and other places

where a higher level security is required.

Wiegand 26~37 bits

26~37bits (default: 26bits)

4bits, 8bits(ASCII), 10 digits Virtual

Number (default: 4bits)

Summary of content (2 pages)

PAGE 1
2 3 4 5 6 7 8 9 0 * # INSTALLATION 3 1 STANDALONE MODE CONTROLLER MODE 5 11 The SK5-X/SK6-X supports 600 users, it support multi access modes in either card access, PIN access, Card+PIN access, or multi cards/PINs access, it can read 125KHz EM & HID for Low Frequency and 13,56MHz Mifare for High Frequency tokens,cards and tags. Another advantage of the SK5-X/SK6-X is it has extra features including block enrollment, interlock, Wiegand 26~37 bits interface, 12~28V AC/DC voltage…etc.
PAGE 2
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.