Service Manual
Table Of Contents
- 627333-A
- 01 Introduction
- Safety
- Follow Safety Instructions
- Prepare for Emergencies
- Safety Alert Symbol
- Signal Words
- Informational Messages
- Important Safety Information
- General Hazard Information
- Emergency Exit From Cab
- Operating The Vehicle Safely
- Prevent Vehicle Runaway
- Use Safety Lights and Devices
- Operating On Slopes
- Traveling On Public Roads
- Stopping And Parking The Vehicle
- System Boom Safety
- Avoid Eye Contact With Radar
- Exhaust Fumes
- Overhead Electrical Power Lines
- Noise
- Handle Fuel Safely - Avoid Fires
- Stay Clear Of Rotating Drive Lines And Moving Parts
- Towing Other Vehicles / Trailers / Equipment
- Modifications
- Maintenance And Service Safety
- Practice Safe Maintenance
- Chemical Safety
- Wear Protective Clothing
- Work In A Clean Area
- Understand Correct Service
- Use Proper Tools
- Support Machine Properly
- Proper Lifting Equipment
- High-Pressure Fluids
- Hydraulic Hoses
- Avoid Heating Near Pressurized Fluid Lines
- Service Cooling System Safely
- Remove Paint Before Welding Or Heating
- Batteries
- Tires And Wheels
- Dispose Of Waste Properly
- Mobile Radio Installations
- Maintenance In The Articulation Joint (Hinge) Area
- Safety Tread and Grip Material
- Safety And Service Decal Locations Chassis
- Safety And Service Decal Locations Cabine
- General
- Dimensions
- Torque Specifications
- Jack Up The Machine
- Tooling list
- Index
- Safety
- 02 Engine
- 03 Powertrain
- Transmission Service Manual
- Transmission and Solenoids
- Testing and Adjusting
- Transmission Troubleshooting
- Disassembly and Assembly
- Drive line
- Index
- TA19 KENR6054-00
- TA19 KENR6678 (Modification)
- 04 Chassis
- MM9L(Modification)
- 05 Cab
- Cab
- Cab Seat
- HVAC
- General Information
- Theory of operation
- Basics of Refrigeration
- Air Conditioning Process
- HVAC System
- Automatic Temperature Control
- Refrigerant Relief Valve
- Temperature Sensors
- Evaporator Coil
- Heater Core (Cab)
- Actuator Motor (Water Valve)
- AirFlow
- Motor (Air Conditioning Blower)
- Speed Control
- Actuator Motor (Damper)
- Glossary of Terms
- HVAC Specification
- HVAC Testing and Adjusting
- Troubleshooting Machine Preparation
- General Troubleshooting Information
- Visual Inspection
- Troubleshooting Faults With Service Codes (Active)
- Troubleshooting Air Conditioner Control
- Problem List
- Probable Causes
- No Display
- Probable Solution
- No Blower Fan
- Probable solution
- No Heat
- Probable Solution
- No Cooling
- Probable Solution
- System is putting out cool air when heat needed
- Probable Solutions
- System is putting out hot air when cooling needed.
- Probable Solution
- No Fan or Erratic Fan
- Probable Solutions
- Nothing Works
- Probable Solution
- Electric Actuator for Mode of Airflow is not Moving or Working Properly
- Probable Solutions
- Refrigerant Compressor Oil - Check
- Refrigerant System - Charge
- Complete Charge of System from a Refrigerant Tank with a Scale
- Adding Additional Refrigerant to an Air Conditioning System with Low Charge
- Manifold Gauge Set (Refrigerant) - Remove
- Control Panel - Test
- Index
- 06 Electrical
- 07 Hydraulic
- 08 Air System
14 KENR6054
Disassembly and Assembly Section
Note: If new bearings are installed, check the end
play of the shaft assembly. Refer to Disassembly and
Assembly, “Transmission - Assemble”.
12. Repeat Step 11 for the other retainers.
g01265831
Illustration 45
13. Use two people in order to install gear assembly
(16). The weight of gear assembly (16) is
approximately 30 kg (70 lb).
g01265829
Illustration 46
14. Use two people in order to install gear (15). The
weight of gear (15) is approximately 23 kg (50 lb).
Install retainer (14) and bolt (13).
g01265805
Illustration 47
15. Apply Tooling (F) to cover assembly (9).
16. UseTooling(A)andasuitableliftingdevicein
order to install cover assembly (9). The weight
of cover assembly (9) is approximately 60 kg
(130 lb).
17. Check the end play of the shaft assembly. Refer
to Disassembly and Assembly, “Transmission -
Assemble”.
18. Position harness assembly (12).
19. Install bracket assemblies (11) and bolts (10).
g01265795
Illustration 48
20. Install O-ring seal (5). Install yoke (8), retainer
(7), and bolt (6).
g01265775
Illustration 49