Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
65
OPERATION
16. Steering
16.1 Steering wheel adjustment
The steering wheel can be height-adjusted by
75 mm and inclined at any angle within 30°.
Operation_Pic_number:1
Height adjustment:
● Lift lever half way.
Height and angle adjustment:
● Pull up lever all the way.
DANGER:
In case of complete failure of the
hydraulic power for the assisted
steering, the tractor remains
controllable. However, greater force
is required to steer.
Do not exceed 10 km/h!
Stop the tractor immediately if there
is a fault with the hydrostatic
steering. Have the fault repaired as
soon as you can at a FENDT service
workshop.
Never adjust the steering wheel
while the tractor is moving!
Fig.114
17. Hydraulics
17.1 General notes on hydraulic
operations
Only operate three-point linkage externally from
a safe position.
For road transport, raise the implement to the
necessary height and lock the operating levers.
Make sure the EPC is positioned in transport po-
sition. When transporting a plough with castor
support wheel, lock lateral stabilisers and un-
hook top link. When cornering, allow for over-
hang and the oscillating weight of the implement.
Before leaving the tractor, fully lower mounted
implements. Switch off the engine and remove
the ignition key. Make sure detached imple-
ments are securely parked.
Three-point implement must have standardised
connection dimensions; if necessary, fit suitable
ball profile for quick-release coupling to towbar
mounting.
Do not operate the hydraulics with cold oil. If ne-
cessary, allow the engine to run at medium
speed for a few minutes.
Stop tractor immediately in case of overheating
of hydraulics.
DANGER:
When working with hydraulic
equipment, make sure no one is
standing within the working area.
Do not stand beneath a raised load.
Always follow the accident
prevention regulations!
When hydraulic operation is
complete, lock all hydraulic valves.
DANGER:
When hitching implements to the
tractor, there is a risk of injury.
Never stand between tractor and
attachment without having first
secured the vehicle to prevent it
from rolling away. (Apply parking
brake, chock the wheels.)