Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
52
OPERATION
Operation_Pic_number:1
Text-module
● Set maximum engine speed in Memory 1
(display A) with rotary control (P1).
● Set minimum engine speed in Memory 2 (dis-
play B) with rotary control (P2).
NOTE:
The maximum engine speed that can be set is
the engine limit speed.
The minimum engine speed that can be set is
the idle speed.
Activating engine control range
F1 = Engine control range active while dri-
ving.
F2 = Engine control range active when front/
rear PTO is engaged.
F3 = Engine control range active when hy-
draulic valve is actuated.
F4 = Engine control range active when lowe-
ring a front/rear power lift.
Function display
Operation_Pic_number:1
Different function displays appear on the main
menu page.
Engine control range active while
driving.
Fig.87
Fig.88
Text-module
NOTE:
Engine control is interrupted if the footbrake
or exhaust brake is actuated. After releasing
the footbrake, engine control is reactivated.
If the tractor is at a standstill and the trans-
mission is in neutral, the engine control for
the front/rear PTO or hydraulic valves or
front/rear power lift is active.
Engine control switches off, if the driver lea-
ves the driver seat for more than 3 seconds
while the tractor is driving and/or the trans-
mission is not in neutral.
Engine control range active while
driving or when front/rear PTO is
engaged or when a hydraulic valve
is actuated or when lowering
front/rear power lift.
Engine control range active when a
front/rear PTO is engaged or when a
hydraulic valve is actuated or when
lowering front/rear power lift.
Engine control range active when a
hydraulic valve is actuated or when
lowering front/rear power lift.
Engine control range active when
front/rear PTO is engaged or when
lowering front/rear power lift.
Engine control range active when
front/rear PTO is engaged or when a
hydraulic valve is actuated.
Engine control range active when
front/rear PTO is engaged.
Engine control range active when
hydraulic valve is actuated.
Engine control range active when
lowering a front/rear power lift.