Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
40
OPERATION
7.5 Driving the tractor
Operation_Pic_number:1
Text-module
Starting off forward from a standstill:
● Press and hold the activating button (C, on
back of joystick).
● If the joystick is moved forward, the tractor
moves off and accelerates forward.
● If the joystick is released, it automatically re-
turns to center position and speed remains
constant.
● If the joystick is pulled back, the tractor slows
down and braking is applied until it comes to
an actuated standstill.
Text-module
Reversing from a standstill:
● Press and hold the activating button (C, on
back of joystick).
● If the joystick is pulled back, the tractor will
move off in reverse and accelerate.
● If the joystick is released, it automatically re-
turns to center position and speed remains
constant.
● If the joystick is moved forward while rever-
sing, the tractor slows down and is positively
braked until it comes to a standstill.
Text-module
NOTE:
It is also possible to operate the joystick first,
then press the activating button afterwards.
NOTE:
Optionally, a warning beep sounds when dri-
ving in reverse.
Text-module
WARNING:
Always engage the gears when
travelling downhill. Do not select
neutral.
At engine speeds over 2600 rpm, the
transmission ratio is no longer
reduced; to reduce speed, apply the
brake.
Fig.53
Turboclutch
The transmission control includes a turboclutch
function. This allows the tractor to be stopped
with the accelerator pedal.
ETNum-list
Deactivating turboclutch function
Operation_Pic_number:1
● Press key (F4). The following sub-menu ap-
pears.
Operation_Pic_number:1
ETNum-list
● Pressing key (F2) switches turboclutch
function on and off.
When the function is on, symbol (A) appears as
shown, when the function is off, the symbol is
shown with a red cross superimposed.
After every cold start, the turboclutch function is
automatically activated again.
Text-module
This means:
1.No engine stalling under difficult conditions.
2.No wheel spinning.
3.Full power transmission from approx.
1,250 rpm engine speed.
Required conditions:
1.Engine is running.
2.No current fault messages.
3.Transmission in neutral.
4.System not in emergency operation.
Fig.54
Fig.55