Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
Important information on service and maintenance
Your tractor will only perform to your complete satisfaction if you take good care of it from the
very start. Your Customer Service Centre will therefore prepare your tractor, free of charge, and
instruct you on how to operate and maintain it.
Protect your claims under Warranty by having all servicing carried out at the correct time by an
authorised FENDT service workshop!
After 50 operating hours (1st service)
After 500 operating hours (2nd service)
After 1000 operating hours (3rd service)
All subsequent maintenance will be carried out at our customer workshops by skilled technici-
ans at reasonable cost and as indicated in the Maintenance Schedule of this Operating Manual.
To extend the life of the tractor, we recommend our annual Major Service, which includes an en-
gine oil change, immediately after the main working season (e.g. the autumn).
During the initial 100 operating hours, it is not advisable to subject the tractor to extreme loads.
Every 100 operating hours, top up engine oil to the upper notch on the dipstick.
Make sure that only FENDT original parts are used for all services and repairs.
Unauthorised changes and modiļ¬cations, and any damage resulting from rigidly mounted
implements (e.g. front loader) not purchased from FENDT, are not covered by the Warranty and
are entirely at the owner's risk. This applies in particular to modiļ¬cations to the power output
limiter and maximum speed settings, and any damage as a result of exceeding the maximum
permissible loads and weights.
Services carried out according to the Maintenance Schedule:
50 operating hours 2000 operating hours 4500 operating hours
First service
Date and signature of mechanic Date and signature of mechanic Date and signature of mechanic
500 operating hours 2500 operating hours 5000 operating hours
Second service
Date and signature of mechanic Date and signature of mechanic Date and signature of mechanic
1000 operating hours 3000 operating hours 5500 operating hours
Third service
Date and signature of mechanic Date and signature of mechanic Date and signature of mechanic
1500 operating hours 3500 operating hours 6000 operating hours
Date and signature of mechanic Date and signature of mechanic Date and signature of mechanic