Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
259
TECHNICAL DATA
X X X Check oil level in axle drives or front PTO gear
1).
Oil level: up to overflow on filler hole.
X X Oil change for axle drives. Oil quantity: Vario 916-920 each side 13.0 l
Oil quantity: Vario 924-930 each side 16.0 l
Oil grade: Fendt Super Trans 85W-90, 80W or Hypoid transmission
oil acc. to API-GL5. SAE 85W-90 or SAE 80W-90 or SAE
90. Not STOU or other any universal oil.
X X Oil change for axle drives with rear axle stub
(optional).
Oil quantity: 16.0 litres each side.
Oil grade: Hypoid transmission oil in accordance with API-GL5. SAE
85W 140 Do not use STOU or any other universal oil.
3 Front axle
X X Check oil level in differential gears and hub
drives.
Oil level up to overflow at check bore, top up if necessary.
X X 1000 Oil change for differential and hub drives. Oil quantity: Differential gears 9.5 Ltr.
Oil quantity: Axle hub each side 4.0 Ltr.
Oil grade: Fendt Super Trans LS 85W-90 or Hypoid transmission oil
with LS additives acc. to API-GL5. SAE 85W-90 or SAE
80W-90 or SAE 90. Not STOU or other any universal oil.
X X X X Check toe-in. Adjust, if necessary. Toe-in: 0 ±1 mm.
4 Hydraulic system
X Replace return line filter.
X 1000 Change oil, including return line filter and air
vent filter.
Oil quantity: about 70.0 l (extraction flow: 50.0 l)
Oil quantity: Maximum fill ca. 100.0 l. (available: 80.0 l)
Oil grade: Fendt Super Hyd, Fendt Extra Hyd 68 or STOU SAE
5W-30, 5W-40, 10W-30, 10W-40, 15W-30,15W-40 or en-
gine oil HD-SAE 5W-30, 5W-40, 10W-30, 10W-40,
15W-30,15W-40 acc. to API-CD.
Also permissible: For temperatures over 10°C, HD-SAE 20 W-20 to API-CD.
every
4 ye-
ars
Replace fine filter for control pressure.
No.
Services
regularly 1)
daily
Job Schedule
See also Operating Manual
Care and Maintenance
General notes and technical data, types of fluid and oil
Correct levels are determined by dipstick check or from the overflow at the
inspection hole.
Observe all accident prevention regulations and comply with directives for
handling and disposing of fluid and lubricants.
1.
50
2.
250
3.
500
4.
750
5.
1000
annu
al or
every
500
every 2
years
or
2000
operating hours