Operating Manual
Table Of Contents
- OPERATING MANUAL
- NUMERICAL INDEX
- SAFETY INSTRUCTIONS
- OPERATION
- 1. Driver seat
- 2. Display instruments and operating controls
- 3. Heating and ventilation
- 4. Rearwiew mirror
- 5. Start-up
- 6. Starting and stopping the engine
- 7. Vario transmission
- 8. Fuel consumption measurement
- 9. Tractor Management System (TMS)
- 10. PTO
- 11. Four wheel drive (4-WD)
- 12. Differential lock
- 13. Front axle suspension
- 14. Power lift and PTO automatic mode
- 15. Brakes
- 16. Steering
- 17. Hydraulics
- 18. Electronic lifting gear control, rear
- 19. Three-point link
- 20. Front power lift
- 21. Trailing devices
- 22. Compressed air system
- 23. Additional ballasting
- 24. Track adjustment
- 25. Twin tyres
- 26. On-board computer
- 27. Computer
- 28. Storing the settings
- 29. Implement control
- 30. Variotronic Ti
- CARE AND MAINTENANCE
- 1. General
- 2. Opening the bonnet
- 3. Engine oil change
- 4. Fuel system
- 5. Dry air .lter
- 6. Cooling system
- 7. V belt
- 8. Brake and clutch system
- 9. Front PTO
- 10. Transmission and axle drives
- 11. Four-wheel drive axle
- 12. Power lift
- 13. Hydraulic system
- 14. Steering
- 15. Front wheels
- 16. Heating and ventilation
- 17. Air conditioning
- 18. Windshield washer system
- 19. Cleaning the tractor
- 20. Electrical and electronic systems
- 21. Fuses
- 22. Wiring diagrams
- IMPLEMENTS
- FAULTS AND REMEDIAL ACTIONS
- TECHNICAL DATA
- ALPHABETICAL INDEX
- Important information on service and maintenance
231
FAULTS AND REMEDIAL ACTIONS
Text-module
Implement control
Text-module
1.2.96 Control unit. Engine cuts out.
1.2.99 Control unit to injection pump
connection is interrupted.
Reduced speed, reduced engine power.
1.2.A2 Engine control unit or injection
pump.
Reduced speed, reduced engine power.
1.2A6 Engine control unit or injection
pump.
Reduced speed, reduced engine power.
1.2.A8 Engine control unit has wrong
value.
Normal operation - fault indication.
1.2.A9 Injection pump. Reduced end speed, reduced engine
power.
1.2.B1 Control unit to injection pump
connection is interrupted.
Reduced speed, reduced engine power.
1.2.B2 Control unit, injection pump. Reduced speed, reduced engine power.
1.2.B3 Interrupted power supply. Engine stops, engine does not start.
1.2.B4 Control unit to injection pump
connection is interrupted.
Loss of enhanced features, only foot
throttle available.
1.2.B5 Control unit, injection pump. Reduced speed, reduced engine power.
1.2.B6 Control unit, injection pump. Reduced speed, reduced engine power.
1.2.B7 Engine speed sensor. Reduced speed, reduced engine power.
1.2.B9 Control unit, injection pump. Engine stops.
1.2.C1 Pump control unit faulty. Engine goes into idle.
1.2.C3 EDC control module - pump
controller connection interrup-
ted.
Engine goes into idle.
1.2.C4 Injection pump. Engine goes into idle.
1.2.C5 Stop solenoid valve. Reduced speed, reduced engine power.
1.2.C7 Injection pump, fuel lines faulty. Engine stops. Check fuel system.
1.2.C8 Control unit, needle movement
sensor, boost pressure sensor.
Engine stops.
1.2.C9 Injection pump. Normal operation - fault indication.
1.2.CA Injection timing mechanism va-
lues not within tolerance.
Reduced rpm, reduced engine power.
Check fuel system.
1.2CB Control unit to injection pump
connection is interrupted.
Loss of enhanced features, only foot
throttle available.
1.2.CD Injection pump. Reduced speed, reduced engine power.
1.2.DE Control unit. Loss of enhanced features, only foot
throttle available.
1.2.EO EDC control unit not connec-
ted.
Normal operation - fault indication.
1.2.E1 PTO rpm or speed signal incor-
rect.
Normal operation - fault indication.
Fault code Cause Effect and remedy
2.1.EO CAN communication E-Box -
CAN joystick defective.
Implements can no longer be controlled
using the joystick.
2.1.EE LBS job computer inoperative. Check CAN bus system for implement
control.
2.1.EF Error message from mounted
implement.
Refer to implement manufacturer's ma-
nual.
Fault code Cause Effect and remedy